R&G LP0209BK Instructions De Montage page 7


Take the tail tidy assembly and offer up to the underside of the bike, fitting the four M6 x 16mm long button
head bolts (item 6) and four M6 washers (item 5) through the four mounting holes on the tail tidy bracket and
into the threaded bosses inside the tail unit, as shown in picture 17.

Take the rubber bung (item 4 – RB0002) and locate through the large central hole on the tail tidy bracket and up
inside the rectangular cutout on the plastic undertray, ensuring the rubber bung sits snugly with the recess of the
bung on the underside, as shown in picture 18.
Page | 7

Feed all three wires though the rubber bung and into the tail section of the bike, as shown in picture 19. Use the
cable ties or self-adhesive cable clips supplied to neaten the routing of the wiring if necessary.

Connect the licence plate illuminator to the connector supplied (item 7 – CON0007), ensuring the bullet
connectors connect black to red and red to black, before fitting the remaining end of the wiring to the OEM
connector already on the bike, as shown in picture 20.

If re-fitting the OEM indicators, re-connect the original wiring connectors to those on the main loom.

If fitting Mini Indicators, use the remaining two connector wires supplied (item 8 – CON0032) to connect the
mini indicators to the main loom as below.

If fitting R&G Aero Indicators the yellow wire on the Aero Indicators connects with the grey or green wire on
the OEM indicator wiring and the black wire on the Mini Indicators connects with the yellow/black wire on the
OEM indicator wiring. 1x set of RGR0001 resistors (available separately) are required to achieve the correct
flash rate.

If fitting R&G Mini Indicators with bulbs, the black/white wire on the Mini Indicators connects with the green or
grey wire on the OEM indicator wiring and the black wire on the Mini Indicators connects with the black/yellow
wire on the OEM indicator wiring.

If fitting R&G Mini Indicators with LED's, the black/white wire on the Mini Indicators connects with the green
or grey wire on the OEM indicator wiring and the black wire on the Mini Indicators connects with the
black/yellow wire on the OEM indicator wiring. 1x set of RGR0001 resistors (available separately) are required
to achieve the correct flash rate.

If illumination fails on any light, re-connect the bullet connectors the other way around.

Check for the correct operation of all lights.

Re-fit the wiring clip and neatly route the wiring with the tail unit.

Ensure the tail tidy is securely mounted and all bolts are fully tightened.

Re-fit the seat.

Re-fit the licence plate (it may require drilling).

Depending on local laws, attach enclosed reflector in an appropriate location.

Test the licence plate illuminator and all lights before riding.
Digital copies of these instructions are available to download from
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer confirms it
has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other
services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is
responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G
shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or
maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident
or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for
indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service
concerned. These terms do not affect the Buyer's statutory rights.
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1 15/09/2016 (AR)
CONSUMER NOTICE
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
R&G Racing
www.rg-racing.com Email:
www.rg-racing.com
info@rg-racing.com