Cleco 120XP Mode D'emploi

ETWB27FR, ETWB135FR, ETWB340FR
ELECTRONIC TORQUE WRENCH WITH ANGLE OPERATING INSTRUCTIONS
LCD Display and Button Functions
Audible Select Unit of
Alert Measurement
• Color LCD • On/Off
Screen • Clear
• Exit Current
Setting
1. Power On
1. Verify torque is not being applied to the wrench. Press
Wrench will beep once.
2. The wrench will default to Peak Torque Mode. The last unit of measurement
and last torque setting will display.
3. The wrench is ready to use.
2. Power Off
1. If no torque is applied, wrench will shut off automatically after 180 seconds.
2. To shut off manually, verify torque is not being applied then press
3 seconds.
3. How to Change Unit of Torque Measurement
1. Power on the wrench as described in Section 1.
2. Press repeatedly to select one of the five torque measurement options:
M
U
NI
· Kg-m
C
S
ET
· Nm
· Ft-lb
· In-lb
· Kg-cm
3. The wrench is ready to use.
4. How to Set Mode
1. There are five mode options:
• P = Peak Torque (default)
• A = Angle
• PA = Peak Angle
• PCt = Target Torque Alert Setting
• trAc= Tracking Mode (optional)
2. Power on the wrench as described in Section 1.
M
3. Press U repeatedly to scroll through the different modes. "SEL" will
NI
show at the top of the screen to indicate the mode being selected. The
C M
U S
NI ET
currently selected mode will still show as an option when scrolling through modes.
C
S
4. Press ET to select the new mode. The screen will show the last setting
for the mode selected.
Note: To exit out of setting mode without changing the mode, press
current mode and setting will remain unchanged.
5. How to Set Target Torque in "Peak Torque" Mode
1. Power on the wrench as
M
U
NI
described in Section 1.
C
S
2. Press . The current torque
ET
setting will display on the screen
with "tor" flashing.
3. The unit of torque measurement can also be adjusted at this time. Press
M
U
NI
to change it if required.
4. Press or C M to select torque value, then press
U S
NI ET
5. The wrench is ready to use.
C
S
ET
6. Apply torque and rotate the wrench at a constant moderate speed until
alerted to stop by the handle vibration, beeps and LCD display. The LCD screen
alternates red/green when the "target torque alert" warning starts. When the
target torque is reached the LCD Screen shows solid red.
Note: After reaching the target torque the display will flash for 10 seconds,
then default to the last setting. The next measurement can be taken while the
screen is flashing by applying force again, or by pressing
last setting.
6. How to Set Angle
1. Power on the wrench as
described in Section 1.
M
U
NI
M
2. Press until the "A" mode is
U
NI
C
reached, then press S .
ET
C
S
ET
3. The screen will show the last angle value set.
M
U
NI
4. If desired angle is displayed, the wrench is ready to use.
M
U
NI
C
5. If you want a different angle, press again to change the angle
S
ET
C
degree. Press or M to get to the required angle, then press
U S
ET
NI
6. The wrench is ready to use.
C
S
ET
7. Apply torque and rotate the wrench at a constant moderate speed until
U
NI
alerted to stop by the handle vibration, beeps and LCD display.
C
8. To take the next measurement press or wait until the display stops
flashing.
Note: After reaching the target angle the display will flash for 10 seconds, then
default to the last setting.
For better accuracy the torque wrench should be rotated between
10 degree/sec – 180 degrees/sec.
7. How to Change "Target Torque
Alert" and "Target Angle Alert"
Percentages
1. Power on the wrench as
described in Section 1.
2. Press M
U
NI
3. Current value will display on screen with "tor" sign flashing
C
S
ET
4. Press
U
NI
Value (+) Change Mode
target torque alert can start at a maximum of 50% to the target torque value
C
or a minimum of 15% to the target torque value. For example, if your target
torque is 100 ft-lbs and your target torque alert is set at 50%, the alert will
start when you reach 50 ft-lbs. Press
M
U
M
U NI
NI
5. The screen will show "Ang" so the target angle alert can be adjusted.
6. Press C
S
ET
C
S
ET
to select when the target angle alert will start. The target angle alert can
start at a maximum of 90 degrees before the target angle or a minimum of 15
degrees before the target angle. Press
7. The wrench is ready to use.
Value (-) • Change Torque
or Angle Value
8. How to Use Pre-Set Torque Values
Setting
• Select Option
1. Power on the wrench as
Displayed M
U
NI
described in Section 1.
• Select Torque
or Angle Value
C
2. Press S
U
ET NI
screen will show the flashing
C
M
U
NI
setting number and the torque value will be displayed.
for 1 second.
C 3. Press
S U
ET NI
4. The wrench is ready to use.
C
9. How to Change Pre-Set Torque Values
Pre-Set Torque Values can only be
selected in Peak or Peak Angle modes.
1. Power on the wrench as
M
U
NI
M
U
NI
described in Section 1.
for
C
S
ET
2. Press
C
S U
ET
and the torque value will be displayed.
C
3. Press
U
NI
for 1 second, the flashing setting number will turn into flashing "tor" sign..
C
4. Now the "tor" sign at the top of the sign will flash. Press
select the desired torque setting, then press
M
U
NI
saved into the Pre-Set options.
5. Press
C
S
ET
10. How to Set Torque with Angle
1. Power on the wrench as
described in Section 1.
U
2. Press
M
U
NI
reached, then press
M
U
NI
C
S
ET
3. The screen will show last angle
C S
ET
and torque value set.
4. If you want a different torque
value or angle , press
U
NI
5. To change the torque value
press or
C
U
NI
required value, then press
C
The screen will show "Ang" sign on
top part of the screen. If the
M
U
NI
target angle value previously displayed
C
. The S is correct, press
ET
The wrench is ready to use.
6. After setting the torque value, the screen will show "ANG". Press
U
NI
or change the angle value. Press
value, then press C
7. The wrench is ready to use.
M
U
NI
C
S 8. Apply torque and rotate the wrench at a constant moderate speed until
ET
alerted to stop by the handle vibration, beeps and LCD display.
Note: After reaching the target torque the wrench will start recording the
M
U
NI
M
U angle measurement. After reaching the target torque and target angle the
NI
C
S
display will flash for 10 seconds, then default to the last setting. To take the
ET
C .
S
ET
next measurement press
11. Low Battery Indication
1. 100%-80% High Battery
M
U
NI
3. 50%-10% Low Battery
to return to the
C
S
ET
M
U
NI
12. Changing Batteries
C
S
ET
1. Use AA (Alkaline) Batteries only.
2. Remove Batteries if the torque wrench is not used for an extended period
of time.
3. Unscrew end cap
M
U
NI
C
S
ET
M
S
ET
M
U
NI
until the "PCt" mode is reached, then press C
S
M
U
NI
or C M to select when the target torque alert will start. The
S
ET
S
ET
M
U
NI
C to save.
S
ET
to change the target angle alert setting. Press
U
NI
M C
U
NI
to save.
C
S
ET
lb.ft
M
then . the
M
S
U
ET
NI
C or M to select the desired pre-set torque value, then press
S
ET
S
ET
lb.ft
then . the screen will show the flashing setting number
M
NI
M
U
NI
S
ET
or to select the desired pre-set torque value, then press
C M
S
ET
M
S
ET U
NI
U
NI
. The new Pre-Set Value is
C
S
ET
C
again to set the target torque as to the new Pre-set value.
M
NI
until the "PA" mode is
C
S .
ET
lb.in
M
U
NI
C again.
S
ET
M
M
U
NI
to get to the
M
S
ET
C .
S
ET
S
ET
M
U
NI
C to exit.
S
ET
U
NI
M
U
NI
C
M
C or to get to the required angle M
S
U
NI ET
again.
S
ET
C
S
ET
M
U
NI
C or wait until the display stops flashing.
S
ET
2. 80%-50% Mid Battery
4. Lower than 10% - Flashing
4. Insert 2 AA (Alkaline) Batteries 5. Replace End Cap
13. Maximum Capacity Exceeded
1. When the applied torque exceeds
M
U the wrench full-scale capacity the
NI
C S
ET
LCD screen will show red. The
display will show "ovEr".
2. Verify the calibration of the wrench if you know its capacity has been
. .
ET
exceeded.
14. New - Tracking Mode
1. Power on the wrench as described in section 1.
2. Press to scroll through the different modes.
M
U
NI
3. Select "trAc" to enter Tracking Mode. There will be a T sign next to the
C
S
ET
battery indication.
M
U
NI
4. In this mode, there will be no target torque or angle value. The display will
U
NI
or C M
S
show the real time torque and value applied to the wrench.
ET
5. You may press to reset the angle value to 0.
C
S
ET
How to Apply Torque
1. This Electronic Torque Wrench is designed so that when force is properly
applied to the handgrip, a continuous audible signal, the LCD screen display
and vibration in the handle will indicate that the Target Torque or Angle has
been attained. DO NOT pull beyond this point.
M
U
NI
C
S Caution: The audible signal, LCD screen display and vibration in the the handle
ET
are indicators that the proper torque or angle have been attained. Over torqu-
M
U
NI
ing beyond these signals could cause fastener failure.
C .
S
ET
2. To properly apply torque, attach socket securely on torque wrench square
drive and position socket on fastener so that tilting will not occur. Grasp the
center of hand grip and apply a slow steady increasing force perpendicular
(90 degrees) to the torque wrench body and perpendicular (90 degrees) to the
center line of the square drive, socket and fastener.
M
U
NI
3. Turn the fastener down with a smooth and even force applied to the handle
C
S
ET
of the torque wrench. As turning resistance increases, pull more slowly. To
assure accuracy, the fastener must be in motion when the torque measure-
ment is made.
M
U
NI
WARNING: Any change from the above procedure will result in a change of
M
U
NI
torque being applied. This includes standard torque wrenches, flex-head
C
S
ET
torque wrenches, universal joints, and universal sockets. DO NOT USE universal
C or M to
S
ET
joints or universal sockets due to the complexity of determining the associated
error. If you need angular access, use a flex-head torque wrench.
S
ET
Extensions
When it is necessary to use an extension that changes the effective lever
length of the torque wrench, torque being applied will change.
M
U
NI
Compute adjustments as follows:
C
S
ET
TW - Torque set on Wrench
TE - Torque applied by the extension to the fastener
M
U
NI
TW = (TE x L) / (L + E)
C S
ET
TE = (TW x (L + E)) / L
M
U
NI
C
S
ET
Notice: Socket extension bars that are axially in line with the square drive do
not cause error and need no adjustment.
Apply torque and rotate the wrench at a constant moderate speed until alerted
to stop by the continuous audible signal, the LCD Screen display and handle
U M
NI
vibration.
C
S
ET
M
Certification
to review
S
ET
This torque wrench was calibrated prior to shipment from the factory within
tolerance limits of:
• Torque (unflexed): +/- 2% CW, +/- 3% CCW from 20% to 100% of capacity
• Angle: (+/- 1% of reading) + (+/- 1 degree @ angular velocity >10 degree/
sec <180 degree/sec) + (+/- 1 degree of test fixture)
Limited Warranty
Until one year from the date of purchase, we will repair any defect in material
or workmanship free of charge. Improper use of these products, including but
not limited to the application of excessive force, will affect performance and
may result in injury. The warranty does not apply to wrenches which do not
function properly or within specified accuracy because of wear, improper or
unreasonable use, damage not resulting from defect or malfunction, or which
have been altered. Calibration is warranted for 90 days. This warranty gives
you specific legal rights, and you may also have other rights which vary from
state to state. For repair or calibration visit www.ClecoTools.com.
www.ClecoTools.com
• Never use the torque wrench with the power off. Always turn on the
torque wrench so the applied torque is measured.
• Do not press any key while torque is being applied.
• Do not use electronic torque wrench to loosen fasteners.
• Verify the calibration of the wrench if you know or suspect its
capacity has been exceeded.
• Periodic recalibration is required to maintain accuracy.
• Never apply more torque than the maximum wrench capacity or the
maximum fastener specifications.
• Do not immerse in fluids.
• Do not use on live electrical circuits.
• Electrical shock can cause injury. Rubber handle is NOT insulated.
M
U
NI
C S
ET
M
S
ET
Apex Tool Group
2630 Superior Court
Auburn Hills, MI, 48236
1.248.391.3700
1.800.845.5629
WARNING
ATG-7373