R&G LP0222BK Mode D'emploi page 9


Cut two small pieces of the self-adhesive foam supplied (item 16) and apply it to the two surfaces on the tail tidy
that are arrowed in pictures 22 & 23.

Take the tail tidy assembly and offer it up underneath the tail whilst feeding the three sets of wires up through
the small hole that is arrowed in picture 24.

Take the four M6 x 16mm long button head bolts (item 4) and four M6 washers (item 5) and fit through the four
mounting holes of the tail tidy before tightening into the threaded bosses on the subframe, as shown in pictures
Page | 9
25 & 26.

Ensure the wiring is pulled up through the opening as shown in picture 27 and fit any cable ties (item 17) and
self-adhesive clips (item 12) to neaten up the wiring on the underside of the tail unit.

Fit the two rubber bungs supplied (item 6 & 7) into the remaining two holes on the underside of the tail unit, as
arrowed in picture 28.

Connect the licence plate illuminator to one of the connectors supplied (item 15 – CON0014), ensuring the bullet
connectors connect black to red and yellow to black, before fitting the remaining end of the wiring to the white
OEM connector already on the bike.

If using the original indicators, reconnect the connectors to those on the main loom.

If fitting Mini Indicators, use the remaining two connector wires supplied (item 15 – CON0014) to connect the
mini indicators to the main loom as below.

If fitting R&G Aero Indicators the yellow wire on the Aero Indicators connects with the black wire on the OEM
indicator wiring and the black wire on the Aero Indicators connects with the yellow wire on the OEM indicator
wiring. 1x set of RGR0001 resistors (available separately) are required to achieve the correct flash rate.

If fitting R&G Mini Indicators with LED's, the black/white wire on the Mini Indicators connects with the black
wire on the OEM indicator wiring and the black wire on the Mini Indicators connects with the yellow wire on
the OEM indicator wiring. 1x set of RGR0001 resistors (available separately) are required to achieve the correct
flash rate.

The R&G Mini Indicators with bulbs do not work on this bike.

If illumination fails on any light, re-connect the bullet connectors the other way around.

Check for the correct operation of all lights.

Re-fit the tail unit bodywork by sliding on from the rear, ensuring all the locating tabs around the tail light fit
correctly and that the black centre panel with lock is fitted in place and the rubber mounted prongs push into
place on both sides, before re-fitting the six push rivets and six bolts to securely fit in place.

Re-fit the riders seat, along with the two mounting bolts on either side of the bike.

Re-fit the side infill panels along with the bolt on both sides of the bike.

Re-fit the pillion seat.

Re-fit the licence plate (it may require drilling).

Depending on local laws, attach enclosed reflector in an appropriate location.

Test the licence plate illuminator and all lights before riding.

The tail tidy can also be used without the indicator bracket fitted, for a sleeker look or if fitted with integrated
indicators within the tail light. If doing this, simply fit the tail tidy as described above, but leave out the indicator
bracket.
Digital copies of these instructions are available to download from
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer confirms it
has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1 24/04/2017 (AR)
CONSUMER NOTICE
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
R&G Racing
www.rg-racing.com Email:
www.rg-racing.com
info@rg-racing.com