Post Installation Checklist - Subaru H101SSJ000 Instructions D'installation

11

POST INSTALLATION CHECKLIST

1. REMOTE ENGINE START- Ensure the Access key is removed from the vehicle, the engine hood, all doors and trunk are
closed. Press the START button on the remote start transmitter two (2) times within three (3) seconds. The vehicle's
parking lights should fl ash and the vehicle's horn should honk one (1) time and then the vehicle should crank and start.
Once started, the transmitter LED will fl ash two (2) times and the parking lights will turn on and stay on signifying the
vehicle is running. The transmitter LED will fl ash one (1) time every three (3) seconds signifying the vehicle is still running.
NOTE: If the vehicle does NOT respond to the remote start transmitters, proceed to SECTION 12 for the
TRANSMITTER PROGRAMMING procedure.
2. CUSTOMER TAKE OVER - While the vehicle is running by the remote engine start, wait at least fi ve (5) seconds and
then confi rm that all functions (lock, unlock & trunk, but not panic) operate properly on the Access key (FACTORY
transmitter). Once the Access key functionality is confi rmed, press the UNLOCK button on the Access key, open the
driver's door and enter the vehicle with the Access key. Press and hold the brake pedal, press the ENGINE START/
STOP button on the dashboard one (1) time and move the shift position lever from the "P" position to the "D" position
and back to the "P" position. The remote engine start should shut down and the transmitter LED should fl ash three (3)
times indicating the system has shut down, but the engine should remain running. Press the ENGINE START/STOP
button on the dashboard one (1) time to turn off the vehicle.
3. ACTIVATION WITH DOOR UNLOCKED - Ensure the Access key is removed from the vehicle, the engine hood, all
doors and trunk are closed and the driver's door is unlocked. Press the START button on the remote start transmitter
two (2) times within three (3) seconds. The vehicle's parking lights should fl ash and the vehicle's horn should honk six
(6) times. The vehicle should not start with the driver's door unlocked.
4. ACTIVATION WITH DOOR OPEN - Ensure the Access key is removed from the vehicle and the engine hood and trunk
are closed. Open the driver's door and press the START button on the remote start transmitter two (2) times within three
(3) seconds. The vehicle's parking lights should fl ash and the vehicle's horn should honk six (6) times. The vehicle
should not start with any door or trunk opened.
5. HOOD SAFETY SWITCH - Open the engine hood and activate the remote engine start. The vehicle's parking lights
should fl ash and the vehicle's horn should honk two (2) times. The vehicle should not start when the hood safety switch
is activated.
6. HEATER / AC FUNCTION - With the Access key inside the vehicle, press the ENGINE START/STOP button on the
dashboard two (2) times to turn ON the ignition. Preset the vehicle's heater or air conditioning to the ON position. Press
the ENGINE START/STOP button on the dashboard one (1) time to turn OFF the ignition and remove the Access key
from the vehicle. Activate the remote engine start and verify that the heater or air conditioning turns on to the preset
setting for manual climate controlled vehicles or turns to the "Full Auto" setting for electronic climate control vehicles.
7. 15 MINUTE RUN TIME - Activate the remote engine start and allow the system to run for the 15 minute preset run time.
The remote engine start should shut down after 15 minutes (+/- 10 seconds).
8. TRANSMITTER FUNCTIONALITY VERIFICATION - Activate the remote engine start using both of the supplied single
button remote start transmitters.
9.
ACCESS KEY (Factory Transmitter) VERIFICATION - Activate the remote engine start using an Access key by pressing
the LOCK button two (2) times within two (2) seconds and then pressing and holding the LOCK button for three (3)
seconds until the parking lights fl ash.
FUNCTIONAL TESTING IS NOW COMPLETE.
PART NUMBER ISSUE
H101SSJ000
DATE
- 21 Dec 2021
SUBARU OF AMERICA
9 OF 10