Preset Stations; Aux-In Connection - SOUNDMASTER PL585 Manuel D'instructions

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 20

Preset stations

You can store up to total of 40 radio stations in the memory (20-FM/20-DAB).
1. Set to FM/DAB mode
2. Turn to the desired radio station by "manual " or " auto " tuning method.
3. Press and hold the "MEM/CLK-ADJ" button (3) around four second to enable memory state, the preset station
will flash on LCD display.
4. Preset the Skip/ Pre up/down button (1) to select the desired station memory for storage.
5. Press "MEM/CLK-ADJ" button (3) to confirm the preset memory.
6. Repeat step 2 to 5 to store other stations.
Recall preset stations
1. Press the "MEM/CLK-ADJ" button (3) once to enable recall state
2. Press "Skip/Tuning
3. Press "MEM/CLK-ADJ" button (3) to confirm the recall memory station.
It is also possible to press "MEM PRE ▲ / ▼" button on remote control, to select the desired memory station.
There are 3 seconds for program state, after 3 sec. This state would resume to normal tuner mode
automatically.
You can overwrite a present station by storing another frequency in its place.
FM-Stereo reception
 Press the " ENTER " knob (2) repeatedly, the FM programs are receiving in mono and stereo mode repeatedly.
In particular when stereo signals are weak, it is preferable to receive the program in Mono.
Hints for best reception:-
-
FM/DAB : the receiver work with detachable DAB/FM wire antenna, made sure the antenna is plugged into the
antenna socket (22), totally unraveled and proper for the best reception.
Please Note - Before Use
Remove the stylus protector.
-
Be sure that the tone arm is being detached from the tone arm rest before operating
-
and re-secured again afterwards.
1. Turn the "FUNKTION" knob (5) to select " Phono/Aux " mode.
2. Set the speed selector (18) to the proper position depending on the record to be played.
3. Place the record on the platter (use the spindle adaptor (17) if required).
4. Lift the tone arm from the rest with the ton arm lift (24), slowly move it to the record side.
The platter will start to rotate.
5. Place the tone arm by the ton arm lift (24) to the desired position of the record.
6. Adjust the volume Knob (13) to the desired level.
7. At the end of record, the platter will automatically stop rotating. Lift the tone arm from the
record and return it to the rest.
8. To stop manually, lift the tone arm from the record and return it to the rest.
Remark : As some kind of record the auto-stop area was out of the unit setting, so it will stop before the last track
finish. In this case, select the auto-stop switch (19) to " off " position, then it will run to the end of the record but will
not stop automatically (turn off the unit by ON/Standby/volume knob (13) or switch back the auto-stop switch to " on
" position to stop the platter rotate). Then put back the tone arm to the rest position.
Connect the unit to any auxiliary device (i.e. MP3 player, or iPod® (not included) by connecting the aux in jack (15)
with one end of 3.5mm stereo cable(not provided) and the other end connect to the auxiliary device to perform the
music.
1. Turn the "FUNCTION" knob (5) to select " Phono/Aux " mode.
2. Plugged the Aux in jack. The channel with switch to Aux automatically.
3. Start to playback your device and adjust On-off/Volume knob (13) to the desire volume level. If the distortion was
too high, reduce the volume level of your auxiliary device.
Remark : due to Aux and Phono were designed at the same position of this system. When Aux in jack (15)
plugged by 3.5mm stereo plug. The channel will change to Aux-in function automatically and turntable will
stop to rotate. Please ensure the Aux in jack (15) without plugged by anything before playing Phono.
or
button (1) to select the desired memory station.
PHONO OPERATIONS

AUX-IN CONNECTION

4
PL585 / English Instruction Manual

Publicité

Table des Matières
loading

Table des Matières