Technical Data - DOLD SAFEMASTER BG 5925/900 Manuel D'instructions

Unit Programming
Notes
Line fault detection on On-button:
The line fault detection is only active when S12 and S22 are switched si-
multaneously. If The On-button is closed before S12, S22 is connected to
voltage (also when line fault across On-Button), the output contacts will not
close.
A line fault across the On-button which occurred after activation of the
relay, will be detected with the next activation and the output contacts will
not close. If a line fault occurs after the voltage has been connected to
S12, S22, the unit will be activated because this line fault is similar to the
normal On-function.
When using light curtains with asymmetric outputs (one output + swit-
ching, one output - switching) the MINUS switching output has to be con-
nected to S22 and the Plus switching to S12.
The gold plated contacts of the BG 5925 mean that this module is also
suitable for switching small loads of 1 mVA - 7 VA, 1 mW - 7 W in the range
0.1 - 60 V, 1 - 300 mA. The contacts also permit the maximum switching
current. However since the gold plating will be burnt off at this current
level, the device is no longer suitable for switching small loads after this.

Technical Data

Input circuit
Nominal Voltage U :
N
Voltage range
at 10% residual ripple:
Nominal consumption:
Min. Off-time:
Control voltage on S11:
Control current over
S12, S22:
Min. voltage between
terminals S12, S22 and S21: DC 21 V when relay activated
Short-circuit protection:
Overvoltage protection:
Output
Contacts
BG 5925.02:
BG 5925.03:
BG 5925.16:
BG 5925.22:
The NO contacts are safety contacts.
The NC contacts 21-22 or 31-32 can only be used for monitoring.
Operate delay typ. at U :
N
Manual start:
automatic start:
BG 5925._ _/901:
Release delay typ. at U :
N
Disconnecting S12, S22:
In the case that S22 is not
disconnected because of fault: ≤ 200 ms
Contact type:
plate
DC 24 V
DC
0.9 ... 1.1 U
N
approx. 2,5 W
250 ms
DC 23 V at U
N
approx. 55 mA at U
N
and U on A1 - A2
N
Internal PTC
Internal VDR
2 NO contacts
3 NO contact
1 NO, 1 NC contact
2 NO, 1 NC contact
40 ms
250 ms
100 ms
15 ms
forcibly guided
M10794
Drawing shows setting at the state of delivery
Technical Data
Nominal output voltage:
Switching of low loads:
(contact 5 µ Au)
Thermal current I :
th
Switching capacity
to AC 15
NO contact:
NC contact:
to DC 13
NO contact:
NC contact:
to DC 13
NO contact:
NC contact:
Electrical contact life
to AC 15 at 2 A, AC 230 V:
to DC 13 at 1 A, DC 24 V:
Permissible operating
frequency:
Short circuit strength
max. fuse rating:
line circuit breaker:
Mechanical life:
General Data
Operating mode:
Temperature range
operation:
storage :
altitude:
Clearance and creepage
distances
rated impuls voltage /
pollution degree:
EMC
Interference suppression:
Degree of protection
Housing:
Terminals:
Housing:
Vibration resistance:
Climate resistance:
Terminal designation:
Wire fixing:
Mounting:
Weight:
Dimensions
Width x height x depth:
14
symmetric:
Ligth bars with symmetric outputs
asymmetric:
Light bars with asymmetric outputs
AC 250 V
DC: see arc limit curve
≥ 100 mV
≥ 1 mA
max. 5 A
see current limit curve
3 A / AC 230 V IEC/EN 60 947-5-1
1 A / AC 230 V IEC/EN 60 947-5-1
1 A / DC 24 V IEC/EN 60 947-5-1
1 A / DC 24 V IEC/EN 60 947-5-1
4 A / 24 V at 0.1 Hz
4 A / 24 V at 0.1 Hz
10 switching cycles IEC/EN 60 947-5-1
5
> 150 x 10 switching cycles
3
max. 1 200 operating cycles / h
6 A gG / gL IEC/EN 60 947-5-1
C 8 A
10 x 10 6 switching cycles
Continuous operation
- 15 ... + 55 °C
- 25 ... + 85 °C
< 2.000 m
4 kV / 2 (basis insulation) IEC 60 664-1
IEC/EN 62 061
Limit value class B EN 55 011
IP 40 IEC/EN 60 529
IP 20 IEC/EN 60 529
Thermoplastic with V0 behaviour
according to UL subject 94
Amplitude 0.35 mm IEC/EN 60 068-2-6
frequency 10 ... 55 Hz
15 / 055 / 04 IEC/EN 60 068-1
EN 50 005
Box terminal with wire protection,
removable terminal strips
DIN rail IEC/EN 60 715
220 g
22.5 x 84 x 121 mm
BG 5925/900 / 13.12.18 en / 048A