Télécharger Imprimer la page

Dolmar PM-411 C Manuel D'instructions D'origine page 11

Tondeuse thermique
Masquer les pouces Voir aussi pour PM-411 C:

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 17
4. TECHNICAL DATA
Model
Engine type
Self Propel
Engine Displacement
Nominal Power
Blade Width
Idle Speed
Fuel Tank Capacity
Oil tank capacity
Grass catch bag capacity
Net Weight
Height adjustment
Guaranteed sound power level at the operator's
position (According to EN ISO 5395-1 Annex F &
EN ISO 5395-2, EN ISO 4871)
Measured sound power level
Guaranteed sound power level (According to
2000/14/EC)
Vibration
(According to EN ISO 5395-1 Annex G & EN ISO
5395-2)
5. ASSEMBLY
5-1 ASSEMBLING THE FOLDING
HANDLE
A) Fix the lower handlebars into the unit body with two
sets of bolt, washer and locking knob as shown.
(Fig. 3, Fig. 4, Fig. 5, Fig. 6)
B) Release the upper handlebars for folding. Connect the
upper handle and the lower handle with the two sets of
bolt, washer and locking knob. (Fig. 7, Fig. 8, Fig. 9)
C) Position all cables over the handle shafts. Clamp them
around the middle of lower handles by the cable
clamps so that the cables are fixed on the outside of
the machine. Otherwise the cables may be pinched by
opening/closing the rear cover or forced by folding the
upper handle. (Fig. 10)
5-2 ASSEMBLING THE GRASS CATCHER
1. To fit: Lift the rear cover and hang the grass catcher on
the shaft of rear of mower. (Fig. 11, Fig. 12)
2. To remove: Grasp and lift the rear cover, remove grass
catcher.
5-3 STARTER HANDLE
Move the starter handle from the engine to the rope guide.
(Fig. 13, Fig. 14)
5-4 HEIGHT OF CUT
Apply outward pressure to disengage lever from rack.
Move lever forward or back to adjust height. (Fig. 15 and
see clause 8-8)
PM-411 C
B&S 500E Series
No
3
140 cm
1.9 kW
410 mm
2,800/min
0.8L
0.47L
50L
26.0 kg
25 - 70 mm, 5 adjustment
84.6 dB (A) (K = 3 dB (A))
93.4 dB (A) K = 1.93 dB (A)
96 dB (A)
2
5.27 m/s
2
K = 1.5 m/s
6. ADJUSTMENT FOR AN
APPROPRIATE HEIGHT
1) Back out the locking knob which fixed the lower
handle. (Fig. 16)
2) Refer to Fig. 17, move the lower handle up and down,
adjust it to the proper height.
There is 3 adjusting height to be chosen on this type
lawn mower; at 1 height, lower handle to the ground is
highest., 3 height is the lowest.
3) Adjusting to the proper height, then fix the lower
handle by the locking knobs.
WARNING: The left side and right side of lower
handle must adjust to the same height.
7. 2 IN 1
These lawn mowers can be retrofitted from its normal
function, based on the application purpose:
From lawn mower with rear discharge and mulching
mower.
What is mulching?
When mulching, the grass is cut in one working step, then
finely chopped and returned to the grass strip as natural
fertilizer.
Hints for mulch-mowing:
- Regular cut-back by max. 2 cm from 6 cm to 4 cm
grass height.
- Use a sharp cutting knife.
- Do not mow wet grass.
- Set max. Motor speed.
- Only move at working pace.
- Regularly clean mulching wedge, housing inner side
and mowing blade.
PM-461 C
B&S 625E Series
No
3
190 cm
2.4 kW
460 mm
2,800/min
1.0L
0.6L
60L
31.1 kg
25 - 70 mm, 5 adjustment
83.5 dB (A) (K = 3 dB (A))
93.6 dB (A) K = 2.47 dB (A)
96 dB (A)
2
5.738 m/s
2
K = 1.5 m/s
11

Publicité

loading

Ce manuel est également adapté pour:

Pm-461 c