Scheppach Air Case Traduction Des Instructions D'origine page 18

• Look out for damage on the device. Check the
device for damage before bringing it into use. Do
not use the device if you discover any defects.
• Do not kink the device's hose, otherwise you may
damage it.
• NOTE! Observe the safety advice provided by the
manufacturer of your inflatable article.
• Do not remove rating plates or labels - they are
safety-relevant parts of the device.
• If you are inexperienced in the use of this type of
device, you should seek out information or training
to learn how to handle it safely.
Do not lose these safety instructions
6. Technical data
Mains connection
Motor rating W
Operating mode
Compressor speed min
-1
Pressure vessel capacity
(in liters)
Operating pressure
Theoretical intake capacity
(l/min)
Protection type
Weight of the unit in kg
*S3 15% = periodical intermediate duty with a duty
cycle of 15% (1.5 min based on a 10 minute period)
The noise emission values were measured in ac-
cordance with EN ISO 3744.
Wear hearing protection.
The effects of noise can cause a loss of hearing.
Noise data
m Warning: Noise can have serious effects on your
health. If the machine noise exceeds 85 dB (A),
please wear suitable hearing protection.
Sound power level (guaranteed) L
95 dB(A) (EN ISO 3744)
Sound power level (measured) L
93,1 dB(A) (EN ISO 3744)
Sound pressure level L 73 dB(A) (EN ISO 11201)
pA
Uncertainty K 2,09 dB(A)
wA/pA
7. Before starting the equipment
• Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
18 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
220 - 240 V~ 50 Hz
max. 1100
S1
3750 min -1
2
approx. 8 bar
approx. 180
IP20
8
wA
wA
• Check the equipment for damage which may have
occurred in transit. Report any damage immedi-
ately to the transport company which was used to
deliver the compressor.
• Install the compressor near the point of consump-
tion.
• Avoid long air lines and supply lines (extension
cables).
• Make sure that the intake air is dry and dustfree.
• Do not install the compressor in a damp or wet
room.
• The compressor may only be used in suitable
rooms (with good ventilation and an ambient tem-
perature from +5 °C to 40 °C). There must be no
dust, acids, vapors, explosive gases or inflamma-
ble gases in the room.
• The compressor is designed to be used in dry
rooms. It is prohibited to use the compressor in
areas where work is conducted with sprayed water.
• The compressor may only be used outdoors tem-
porarily when the weather is good. Always keep
the compressor dry and do not leave it outdoors.
8. Attachment and operation
n Important!
You must fully assemble the appliance before
using it for the first time!
8.1 Mains connection
• The compressor is equipped with a mains cable
with shock-proof plug. This can be connected to
any 230-240 V~ 50 Hz shock-proof socket which is
protected by a 16 A fuse.
• Before you use the machine, make sure that the
mains voltage is the same as the operating voltage
(see the rating plate).
• Long supply cables, extensions, cable reels etc.
cause a drop in voltage and can impede motor
start-up.
• At low temperatures below +5°C, sluggishness
may make starting difficult or impossible.
8.2 ON/OFF switch (Fig. 1)
• To switch on the compressor, press the button (2)
on position I.
• To switch off the compressor, press the button (2)
on position 0.
8.3 Setting the pressure (Fig. 1)
• Use the pressure regulator (8) to set the pressure
on the pressure gauge (7).
• The set pressure can be drawn from the quicklock
coupling (6).
• The vessel pressure can be read off the pressure
gauge (4).