Sicce Syncra SDC Mode D'emploi page 28

When the PRESET programs are activated, the LEDs of the central ring follow the variations in flow rate provided by the program.
EN
After some minutes from the last touch all the LED lights will decrease in intensity for energy saving and the controller
will be in LOCK mode.
To unlock the Keypad make a light SHORT pressure on the central key.
IT
LOSS OF WI-FI CONNECTION AND NOTIFICATION
In case Wi-Fi connection is lost, the pump will continue working and the user will receive a notification via email if this
DE
warning has been activated in the APP CONTRALL.The connection will be restored automatically as soon as the wireless
network is available again.
MAINTENANCE
FR
For the periodic maintenance of the pump, unplug the pump from the electric socket and then remove the pump from water.
1) Lift the plastic ring of the pump's volute pulling the tab outwards (Pic. 6).
2) Remove the ring (Pic. 7).
ES
3) Remove the volute of the pump by turning and simultaneously pulling forward (in the case of fouling this may take
more pressure).
4) Pull out the complete rotor set (Pic. 8).
5) Rinse each part with water, using a soft brush to remove the deposit.
NL
6) Then assemble everything in the inverse order.
7) Put the ring in place with the biggest teeth facing the pump and close it by pressing on the tab until you hear a "click". (Pic. 9)
Any damage to the o-rings, even small, can seriously endanger the pump performance. In this case, it is best to replace them.
PT
IMPORTANT: The build-in circuit board of the pump has been programmed to provide 3 levels of protection:
· Protection against rotor's blockage: In case of malfunction which causes the lock of the rotor (due to excessive dirt
or other) or of operating without water, the pump, will initiate 10 startup attempts to turn the pump on correctly. If after
10 attempts this does not happen, the pump will stop automatically and remain in standby. The controller will remain
RU
powered, but the engine will shut down. In this case to restart the pump you need to disconnect the plug for about 30
seconds and re-insert it into the power socket.
· Dry running protection: motor's protection in case of functioning without water. The pump stops when it works without
CN
water, or if there is a locked rotor. When the pump is taken out from the water, the motor stops.
· Thermal protection: when the buil-in electronic board detects a temperature increase outside the working parameters of
the pump, it turn the pump off to avoid damage to components or to the motor.
ATTENTION! Do not underestimate the power of the magnet. If you slightly loose the grip and the axis hits the rear
bearing, the risk to damage the bearing is very high. A damage axis and bearing causes high reparation costs.
CONTROLL APP AND ALERTS SYSTEM
In the cases described above, if the user has downloaded the ContrALL APP and activated the alert system in the profile
session, he will receive notifications so that action can be taken in real time.
SPECIAL MAINTENANCE AND REPLACING GROUP ROTOR
Follow this instruction for an accurate rotor kit cleaning or replacing
Repeat the opening actions as indicate in Maintenance' section, steps 1,2,3,4.
To easily remove the bottom bearing, we suggest to leave the pump submersed with water and Pump Clean for a while
to make soften debris or limestone.
· Insert the hook ( accessory) inside the tube of the pump. (Pic. 10).
· Hook the bearing and pull it out.
· Clean the bearing under running water (never use soap or detergent of any kind because they pollute the aquarium water:
we recommend using a vinegar and water solution) possibly using a soft brush to remove scale deposits. If it is heavily
worn we suggest to replaces it with a new one.
· Re-insert the bearing sleeve in the pump (Pic. 10)
DEEP CLEANING- USE SICCE PUMPCLEAN ( PIC.12)
It's important to keep your Sicce Pump in prime operating condition to ensure long-life and efficient operation. Over time,
natural mineral deposits will form in the filter surface and rotor, and if untreated, may cause undesirable operation or even
failure. Sicce PUMPCLEAN is a super-concentrated, yet completely safe solution to remove these deposits and keep your
filter in tip-top shape.
ATTENTION! The limestone deposits and the natural wear-out of the components might cause a raise of the pump's noise.
However, they do not affect the good functioning of the pump. In this case, we recommend you to replace the impeller.
ONLINE HELP
Watch our tutorial videos on THE SICCE YOU TUBE official channel: www.youtube.com/SICCEspa.
28
( )
( )
(
( )
( )
) ) after wetting and push it all the way.
( )
( ).