Sicce Syncra SDC Mode D'emploi page 27

Do not position the pump above the water level (Pic. 2)
The risk of invisible air bubbles creating a vacuum area is very high. Damages which are caused by the pump running dry
are excluded from warranty.
To maximize the pump's efficiency, choose a straight inlet tube without elbows (Pic. 3).
We suggest an Inlet and outlet tubes with diameter equal or bigger than the diameter of the threaded pipe included (Pic. 4).
Do not use the pump leaving the outlet totally closed. A minimum water flow is necessary to keep the inner motor cool
without running dry (Pic. 5). ( )
CONTROLLER USE AND PUMPS REGULATION
By connecting the power supply to the controller, all the LEDs light up once. After about 20 seconds the WIFI symbol will
start to flash slowly to indicate that it is ready and awaiting the set-up. If the controller has already been set-up, once
powered, the WI FI automatically reconnects to the network and reloads the programs set in the CONTRALL APP.
Because the controller keys are capacitive, simply place your finger on the surface and apply a light pressure to use it.
SYNCRA SDC 3.0 - PSK 2600-4000
To activate the pump, keep the right key (+) pressed for 3 ". As a test, all the LEDs light up for a few seconds. The pump T T
starts at 30% of the operating range. Pressing the keys (+) and ( -) it is possible to increase or decrease the pump
flow. Consequently, the luminous intensity of the 5 LEDs will vary. The pump symbol will light up in the color set via
the CONTRALL app. The Wi-Fi symbol will flash blue slowly while waiting to be connected to the Wi-Fi network via the
CONTRALL App. If the pump is managed via CONTRALL, it will not be possible to modify its operation using the controller.
It will only be possible to switch it off by keeping the right key (+) pressed for 3 ".
The Controller supplied can only regulate the flow. It can only be powered with the included transformer and manages only
the supplied pump. Any other use could irreparably damage the device and void the warranty.
WI-FI SET UP
CONTRALL App Free download
Select MY DEVICES and tab on +
Choose Syncra SDC or PSK and then Model 3.0 or 2600- 4000
Read the text and then Confirm PROCEED
Next: select the Wi fi network you wish to link the pump and the Wi-Fi psw.
Give a name to your pump and confirm with DONE.
SYNCRA SDC 6.0-7.0-9.0
All the LEDs flash simultaneously at the first power-up or after a black out. This means that the controller has not (first
power-up) or has lost (black out) the ECO and PAUSE already made setting, which need to be set up again. Holding down
the ON/OFF button for 4 seconds the LEDs will stop flashing. The flashing ends autonomously when, after a black out, the
WI FI controller reconnects to the network and reloads the pump's settings done with APP CONTRALL.
- Pump ON / OFF: LONG TOUCH of the central key ( Pump ON = 1st LED Blu colour is on)
- When the pump is OFF and then ON again, the pump starts from where it was set up when you stopped it.
- SHORT TOUCH: : LOCK / UNLOCK of the keyboard. When you lock it , the symbol LOCK is red.
- To set the pump's water flow turn clockwise ( the flow goes up) and counterclockwise ( the flow goes down) with
your finger the "SPEED" area of the controller . The led lights will be on and will follow your finger to indicate where you
are with the pump's regulation.
- The WI FI connection is always active as indicated by the flashing symbol
When the pump and controller are powered, it may take a few seconds for the WI FI connection to become active.
When the PRESET programs are activated, the LEDs on the bar follow the variations in flow rate preset by the program.
The Controller supplied with Syncra 6.0 - 7.0 - 9.0 SDC models replicates all the features of CONTRALL with the only
exception of the CUSTOM function. It can be powered only with the included transformer and manages only the pump
supplied. Any other use could irreparably damage the device and void the warranty.
Wi-Fi & CONTROLLER Reset: by the LONG TOUCH of both ECO and PAUSE keys the Wi-Fi will be reset. The Wi-FI symbol
will remain on without flashing. The restore operation will last 11"
SET UP SYNCRA 6.0-7.0-9.0
The SHORT touch of key MODE drives you into the PRE-SET MODE section: small decreases of speed, which are
"variations" of the set speed. They will be random for the first three MODE, sinusoidal for the last two, until you return to
NO MODE mode (all LEDs off) Pic. D.
With a SHORT TOUCH "ECO" the pump will remain in ECO for 7 hours. During this time the white LED in the left side
under the key ECO will be ON. This setting will start again automatically after 24hours .
With a LONG TOUCH "ECO", in the SPEED area you set up the reduced speed for ECO; during this setting the LED of the
round side which indicates the speed level will be flashing together with the blu one in the right side under the key ECO.
By a new LONG TOUCH you will record the selected speed level.
With a SHORT TOUCH "PAUSE" the pump will work for 10 minutes at reduced speed. The white led under the key PAUSE
will be on. This function will start again automatically after 24 hours.
With a LONG TOUCH "PAUSE", in the SPEED area you set up the reduced speed for PAUSE. The LED of the central area,
which indicate the pump's speed, will be flashing together with the blu led on the left side under the key PAUSE. By a new
LONG TOUCH you will record the selected speed level.
WI-FI icon with LIGHT BLU on, it means that the WIFI connection is active.
It may take few seconds before the connection is active.
( ) ) because it is not self-priming and the risk of the pump to run dry.
( )
EN
( )
IT
DE
FR
ES
NL
PT
RU
CN
27