Publicité
Les langues disponibles
Les langues disponibles
Operation
Preparation
Keep the packaging material for safe storage or
transport later.
f Check that the contents are complete.
f Check all the parts for possible transport damage.
Safety
Caution! Damage due to incorrect power supply.
f Only operate the appliance with the voltage stated
on the nameplate.
Charging the battery
1. Connect the appliance plug (Q) on the plug-in transformer
to the charging stand socket (H) (Fig. 4ⓐ).
·
The appliance can also be connected directly to
the plug-in transformer for charging (Fig. 2ⓐ/ⓑ).
·
Battery overcharging is prevented thanks to intelli-
gent charge management.
2. Connect the plug-in transformer to the mains socket
(Fig. 4ⓑ).
3. Switch off the appliance using the on/off switch (Fig. 3).
4. Place appliance in the charging stand (Fig. 4) or connect
directly to the plug-in transformer (Fig. 2ⓐ/ⓑ). The charg-
ing process starts.
·
During the charging operation, the LED display
on the on/off switch (B) flashes green. The charge
status of the battery is displayed by corresponding
bars on the battery power indicator (C). When
the battery is fully charged, all bars on the battery
power indicator and LED display on the on/off
switch are illuminated.
·
After the appliance has been removed from the
charging stand, the display goes out after approx.
15 seconds (power saving mode).
·
The accuracy of the battery power indicator (C)
can be increased by fully discharging the battery
from time to time and then recharging it in one
uninterrupted charging process.
It should take around 45 minutes for the appli-
·
ance to charge to full capacity.
5. As soon as the battery is fully charged, all bars on the bat-
tery power indicator and LED display on the on/off switch
are illuminated.
Battery operation
1. Switch on the appliance using the on/off switch and switch
off after use (Fig. 3).
·
After the appliance has been switched off, the
display goes out about 15 seconds later (power
saving mode).
·
When the battery is fully charged, the appliance
can be used for up to 75 minutes without mains
connection.
·
The charge status of the battery is displayed by
the battery power indicator (C).
·
In case of insufficient maintenance of the
blade set, the operating time can be reduced
considerably.
Mains operation
1. Connect the appliance plug (Q) on the plug-in transformer
to the appliance socket (E) (Fig. 2ⓐ).
2. Connect the plug-in transformer to the mains socket
(Fig. 2ⓑ).
3. Switch on the appliance using the on/off switch and switch
off after use (Fig. 3).
Operation
Setting the cutting length
The cutting length can be adjusted to between 0.7mm and 3mm
(5 possible positions) using the cutting-length adjustment inte-
grated into the blade set (Fig. 5).
Cutting with the attachment comb
The appliance can also be operated with attachment combs.
f In order to achieve the indicated cutting length, the cutting
length adjustment lever should be set to position 1 (Fig. 5).
Depending on the model, the following attachment
combs are included as standard:
3 mm, 6 mm, 9 mm and 12 mm, 18 mm and 25 mm
cutting lengths.
Attaching/removing the attachment comb
1. Slide the attachment comb on to the blade set in the direc-
tion of the arrow until it reaches the limit stop (Fig. 6ⓐ).
2. The attachment comb can be removed by pushing it in the
direction of the arrow (Fig. 6ⓑ).
ENGLISH
de
en
fr
it
es
pt
nl
da
sv
no
fi
tr
pl
cs
sk
hr
hu
sl
ro
bg
ru
uk
et
lv
lt
el
ar
13
Publicité
