Important Information To Wa 950 / Wa; General; Scope Of Supply 0 986 400 A00N And 0 986 400 A01N Respectively; Assembly - Nussbaum WA 950 Instructions De Montage

1.

Important Information to WA 950 / WA 970

Dear Customer,
The Wheel Aligner WA 950 / WA 970 differs from the one
described in this manual in the following points:
1. Ergonomically designed sensor head casing with a big
handle.
2. Power button instead of power switch on the sensor
heads.
3. Elektronic bubble level in five instead of three steps on
the sensor head.
4. Quicker data transfer protocol: In the password pro-
tected setup, you have to select sensor head type
‚Cable Sensors 2008' or ‚Radio Sensors 2008'. If you
do not get the Aligner model WA 950 / WA 970
correctly displayed at the start screen of the Alignment
program, this setting is done incorrectly. Data commu-
nication will not work.
5. The internal electrical setup of the machine is simpler.
Instead of a triple DC power supply board with three
LEDs as described, there is only one single 12V DC
switching power supply for everything. Instead of the
thick, red sensor canbles, there are thinner, but more
robust black sensor cables with a plug that is molded
on.
6. Radio Aligners WA 970 : Data transmission is done
with a similar black transceiver box that is plugged in on
top of the cabinet.
But this one is working in the 2.4GHz range (instead of
the 433MHz used up to now). If needed, you can select
a different channel with a small service program that is
called from the password protected setup area.
The batteries are the same as in the WA 920 aligners.
These are off-the-shelf 7.2V 3000mAh NiMH batteries
in ‚Racepack' form.
The big difference is that the intelligent charge control-
ler is no longer inside the cabinet, but inside each
sensor head.
The batteries will even charge when the sensor head is
connected via cables during a measurement.
The new machines are explicitly identical with the existing
range concerning these points:
- Software protection system with smartcard reader and
SIM/Smartcards used are. Measurement process, run-
out compensation, vehicle selection, datenbank,...
- Same Software Installation is being used, only correct
selection of sensor type in setup required- Identical
alignment accessories (e.g. wheel clamps, turntables,
unlocking smartcards,...)
- Same after sales tools are being used (e.g. calibration
rig)
- Many identical spare parts (mechanical parts, toe caa-
meras, batteries,...)
24
1.1

General

Before starting work, the power supply must be swit-
ched off and locked so as to prevent it from being
switched on again accidentally.
For reasons of safety, assembly of the WA 900 trolley
may only be done with the aid of an assistant.
It is essential to read through the installation and opera-
ting instructions before using the wheel aligner for the
first time.
1.2 Scope of supply 0 986 400 A00N and 0 986 400 A01N
respectively
- Steering wheel brake
- Brake pedal depressor
- Logging printer
- Monitor 17"
- Set of clamps, manual (4 pcs)
- Bedienungsanweisung
- Operating instructions
- CE statement (only WA 900)
- CE statement (only WA 920)
- CD-ROM with program
- Set of cables and sensors (only WA 900)
- Set of radio sensors (only WA 920)
- PC unit
- Trolley
Please check the scope of supply!
1.3

Assembly

Unpack the parts upon receiving the shipping box. The trolley is
largely preassembled and only needs to be equipped with the PC
unit, the keyboard, the logging printer and the monitor.
See the relevant installation instructions that are inclu-
ded with the corresponding units.
1 987 009 A17N
1 987 009 A16N
0 986 400 U02N
0 986 400 U00N
1 987 009 A08N
1 689 979 873N
1 689 978 435N
1 987 009 AD0N
1 987 009 AD1N
1 987 009 AS6N
1 987 009 A19N
1 987 009 A14N
0 986 400 U01N
1 987 009 A23N
08.12.08 1 689 978 435N