Teranex Mini - Sdi To Analog 12G - Blackmagic Design Teranex Manuel D'utilisation Et D'installation

Teranex Mini - SDI to Analog 12G

Convert from SD SDI, HD-SDI, 3G-SDI, 6G-SDI and 12G-SDI
input sources to analog component, NTSC and PAL video
out, plus balanced AES/EBU and analog audio out. The
built in down converter lets you connect 12G-SDI video to
1 2
Connectors
1. Mini-B USB port
Connects to the Blackmagic Teranex Setup software via
a Mac OS X or Windows computer for adjusting settings
and updating your Teranex Mini's internal software.
2. Switches
Adjustable switches for changing settings.
3. LED Multi-Use Indicator
Glows white when the converter is receiving power and
green when a valid video input signal is detected. Will flash
on/off to identify individual converters via Blackmagic
Teranex Setup.
4. Power
Standard built in IEC C14 connector for 90 - 240 volt AC
power supply.
5. Y or NTSC/PAL
Analog component Y, NTSC or PAL composite output
BNC connector.
6. B-Y or S-VIDEO Y
Analog component B-Y, or S-Video Y output BNC connector.
Switches
Teranex Mini SDI to Analog 12G's switches provide the
following settings:
Switch 8 - Analog Audio, AES/EBU Audio
Set switch 8 to 'off' to select balanced analog audio, or to
'on' for digital AES/EBU audio output.
Switch 7 - 7.5 IRE, 0.0 IRE
The USA and countries using NTSC with 7.5 setup should
set switch 7 to 'off'. If you're working in countries not using
7.5 setup, set switch 7 to 'on'. This setting only affects
composite or S-Video outputs.
SD and HD analog equipment and easily connects to video
monitors and decks such as Betacam SP and VHS. You
can even output pairs of analog audio from 16 de-embedded
SDI audio channels.
4 5
Y or NTSC/PAL
ETHERNET PoE+
3 8
7. R-Y or S-VIDEO C
Analog component R-Y, or S-Video C output BNC connector.
8. Ethernet PoE+
Connects to a network switch or computer so you can
change settings using Blackmagic Teranex Setup.
The Ethernet port also supports power over Ethernet plus.
9. SDI IN
SDI video input BNC connector.
10. SDI Loop Out
SDI video loop output BNC connector.
11. L - Analog or AES/EBU
Balanced left channel analog audio, or digital AES/EBU
audio output XLR connector.
12. R - Analog, AES/EBU or Timecode
Balanced right channel analog audio, or digital AES/EBU
audio output XLR connector. Can also be configured for
timecode output.
Switch 6 - SMPTE Levels, Betacam Levels
Set switch 6 to 'off' for SMPTE levels, or 'on' for Betacam
levels. SMPTE levels are more common and even Betacam
SP decks can use SMPTE levels, so only switch this to
Betacam if you are sure that Betacam levels are being used.
Switch 5 - Component, Composite or S-Video
Set switch 5 to 'off' to select analog component video
output, or 'on' for composite and S-Video outputs.
To display the HD video input as SD on the S-Video and
composite outputs, down conversion must be set to 'on'
19
6 7
B-Y or S-VIDEO Y R-Y or S-VIDEO C
L - ANALOG
SDI IN SDI LOOP OUT AES/EBU
9 10 11
R - ANALOG
AES/EBU - T/C
12