Presentation - Ayrton arcaline2 3G Mode D'emploi

Please consult your AYRTON dealer for further information on
this type of installation.
Do not place anything on top of the ARCALINE2 3G. Under
no circumstances must it be installed in such a way that it
enables a person, vehicle or ant object to move over or stand
on the projector.
Never project or allow hard, heavy or blunt objects to fall on
your ARCALINE2 3G, not to mention any objects made of
glass or porcelain (bottles, crockery, balls, etc). The projector
is made up of solid materials such as extruded aluminium
and tempered glass, which makes it highly resistant, but not
unbreakable. Any hard materials such as steel or glass that
fall on the unit are likely to break or cause damage to the
glass or body of the unit. AYRTON cannot be held liable for
any breakages of the unit glass or body, which is not included
in the warranty.
The ambient temperature in the location where your
ARCALINE2 3G is installed must not exceed Ta = 40°C.
Warning :
The temperature of the glass surface of your ARCALINE2 3G
is likely to reach 45°C, depending on its use. The temperature
of the aluminium body of the device is likely to reach 80°C.
Make sure that the setting in which you intend to install the
projector is compatible with this temperature.
The supply voltage required by the ARCALINE2 3G projector
is 110 to 230V AC. Make sure that the setting in which you
intend to install your projectors is compatible with this.
Check that the support on which you fix your ARCALINE2 3G
is able to handle the weight of this device safely, i.e., 7.9 kg,
including all of the required safety coefficients.
Do not use your ARCALINE2 3G before familiarising yourself
with these recommendations and do not authorise work to
be carried out on it by unqualified personnel.
When transporting your ARCALINE2 3G, it is strongly
recommended that you use the original packaging.
Should your ARCALINE2 3G not be used for a long period of
time, disconnect the device from the mains.
Your ARCALINE2 3G must not be thrown away with the
rubbish, it must be recycled. Please consult the legislation in
force in your country on recycling electronic devices.
WARNING !
The "series" connection of the power supplies
On the arcaline2 3g (input and output connections to
the mains of the connected units) is limited, for safety
The maximum authorised quantity is :
8 Arcaline2 3g projectors on the same mains circuit
4 Arcaline2 3g projectors on the same mains circuit
(Electric circuit protected by a 10-amp circuit breaker)

Presentation

The ARCALINE2 3G is a waterproof linear luminaire (protection
index IP65) with the very latest generation, high performance
LED type light sources (Light Emitting Diodes).
The unit is controlled remotely via a DMX512 type external
control signal.
This projector is available in two versions with different LED
sources, each adapted to a specific type of lighting :
Full Colour Version :
This projector integrates 4-colour multi-chip LEDs : Red,
Green, Blue and White.
It is a projector with coloured light, operating on the
principle of additive colour mixing with white light, which
allows for a the oretical range of colour rendering of 4.2
billion colours.
CTC Version :
This projector integrates 4-colour multi-chip LEDs
combining Cold White (7000°K) and Warm White
(2700°K) sources.
It is a projector with variable white light, which allows for
a colour temperature range adjustable from 2700°K to
7000°K.
The ARCALINE2 3G is a luminaire that is approximately 1
metre in length, and combines a total of 64 LED light sources
in 16 groups.
Depending on the version of the unit (Full Colour or CTC),
it requires 2 to 11 DMX circuits for control by an external
control system emitting a DMX512 signal (see further down
in this manual for details).
For setting its parameters (DMX address, DMX operating
modes and various options), the ARCALINE2 3G requires
6 USER MANUAL
reasons.
In 230v ac
Or
In 110v ac.