Behaviour In An Emergency Situation; Safe Handling Of Fuels; Description Of Device / Spare Parts; Assembly - ATIKA V 11000 Notice Originale

Behaviour in an emergency situation

 Initiate all required first aid measures suited for the injury and seek
qualified medical advice as quick as possible.
 Protect the injured person against further injuries and immobilise
the injured person.
Safety Precautions - Safe handling of fuels
Fuels and fuel vapours are inflammable and may cause
serious injury on the skin or when inhaled. Therefore be
careful and provide sufficient ventilation when handling
fuels.

Do not smoke and avoid open flames when fuelling.

Wear gloves when fuelling.

Do not fuel in closed rooms.

Stop the machine and allow it to cool down.

Carefully open the tank cap to relieve possible overpressure.

Avoid spilling of fuel or oil. Clean the device immediately when you
have spilled fuel or oil. Change your clothes immediately when you
have spilled fuel or oil on them.

Make sure no fuel can enter the soil.

Carefully close the tank cap after fuelling and check that it does not
get loose during operation.

Check that there is no leakage on the tank cap and fuel lines. If
there are leaks this product may not be started.

Never use a device with damaged ignition cable and spark plug
connector.Risk of sparking.

Only transport and store fuels in containers approved and identified
for this purpose

Keep children away from fuels.

Do not handle and store fuels close to combustible and highly
inflammable materials as well as sparks and open flames.

Go away at least three metres from the fuelling place to start the
machine.

Description of device / spare parts

 Please refer to the attached assembly and operating
instruction sheet.
Pos
Name
(in part without
illustration)
1 Gasoline engine
3a Handle, assy.
4 Throttle lever
5 Wheel
6 Axle
7 Securing pin
8 Undercarriage
9 Pin dia. Ø 14 x 100
10 Rubber mat
11 Clamping plate
12 Motor oil filler plug
13 Eccentric oil filler plug
14 Sealing ring for eccentric oil filler plug
15 Tank cap
16 Fuel inlet filter
17 Fuel tank
18 Choke lever
16
19
20
21
22
23
24
25
26
27
28
29
32
33
34
35
36
37
38
39
40
41
Handle
Secure the handle assy. (3a) with 2 hexagon screws M 10 x

20, 2 washers A 10.6 and 2 spring rings Ø 10 to the vibratory plate.
Secure the throttle lever (4) with a hexagon screw M 5 x 25

and washer to the handle
Undercarriage
Slide the wheels (5) onto the axle (6) and secure them each

with a spring pin and washers.
 Detach the spring pin and pull out the axle journal. Secure the
axes in the shown position using the spring pin.
 Insert the bracket of the undercarriage (8) between the
retainer of the vibratory plate. Connect both by pushing the pin dia.
Ø 14 x 100 (9) through and securing it with a spring pin.
 Slightly pull back the securing pin (7) if the pin cannot be pushed
through freely.
R u b b e r m
R u b b e r m
 Place the vibratory plate on the rubber mat.
Order
 Secure the rubber mat (10) with the clamping plate (11), 3
number
hexagon screws M 10 x 30, 3 spring rings Ø 10 and 3 washers A
10 to the base plate.

Use the rubber mat only when compacting paving stones,
372932 
372921
concrete slabs or similar.
372915
Other materials such as gravel, crushed gravel, etc. must not be
372916
worked on with the rubber mat.
372910
372918
372908
372958
372959
-
-
372927
372960
372931
-
-
Ignition switch
Cranking rope handle
Cranking rope
Belt cover
Lock nut
V-belt
Tensioning screw for V-belt
V-belt pulley for motor
V-belt pulley for eccentric
Air filter cover
Air filter
Air filter mounting plate
Spark plug connector
Spark Plug
Spark plug socket spanner
Silencer/exhaust outlet
Oil drain hose
Sealing ring for oil drain plug
Safety label
Air filter seal
Transport linkage

Assembly

a t
a t
-
-
-
372940
-
372941
372939
-
-
372924
372923
-
-
372968
381846
-
-
-
372907
372925
372913