Télécharger Imprimer la page

Skil 0130 Notice Originale page 12

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 14
Never use the tool when handle cord is damaged, have it
replaced by a qualified person
AFTER USE
Store the tool indoors in a dry and locked-up place, out
of reach of children
- store the battery pack separately from the tool
BATTERIES
The battery supplied is partially charged (to ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
first time)
Only use the following batteries and chargers with
this tool
- SKIL battery: BR1*31****
- SKIL charger: CR1*31****
Do not use the battery when damaged; it should be
replaced
Do not disassemble the battery
Do not expose tool/battery to rain
Permitted ambient temperature (tool/charger/battery):
- when charging 0...+45°C
- during operation –20...+50°C
- during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL
4 Read the instruction manual before use
5 Batteries may explode when disposed of in fire, so do not
burn battery for any reason
6 Store tool/charger/battery in locations where temperature
will not exceed 50°C
7 Do not dispose of electric tools and batteries together
with household waste material
8 Beware of sharp blades, after switching off the tool the
blade continues to rotate for a few seconds, switch
off and remove safety key from tool before cleaning/
maintenance.
9 Pay attention to the risk of injury caused by flying
debris (keep bystanders a safe distance away from work
area)
q Wear protective glasses and hearing protection
w Do not expose tool to rain
USE
Charging battery
! read the safety warnings and instructions
provided with the charger
Battery level indicator e
- press the battery level indicator button N to show the
current battery level e a
! when the lowest level of the battery indicator
starts flashing after pressing button N e b, the
battery is empty
! when 2 levels of the battery indicator start flashing
after pressing button N e c, the battery is not
within the allowable operating temperature range
Battery protection
The tool is suddenly being switched off or prevented from
being switched on, when
- the load is too high --> remove load and restart
- the battery temperature is not within the allowable
operating temperature range of -20 to +50°C --> 2
levels of the battery level indicator start flashing when
pressing button N e c; wait until battery has returned
within the allowable operating temperature range
- the battery is nearly empty (to protect against
deep discharge) --> a low battery level or flashing low
battery level e b is shown by the battery level indicator
when pressing button N; charge battery
! do not continue to press the on/off switch after the
tool is switched off automatically; battery may be
damaged
Removing/installing the battery r a
- 2 battery packs need to be installed
Removing/installing safety key M r b
Adjusting height of tool handle t
Adjusting cutting height (25-75 mm) y
- adjust handle F by putting it in slot for desired cutting
height. 1 = 25mm, 2 = 35mm, 3 = 45mm, 4 = 55mm, 5
= 65mm, 6 = 75 mm
On/off safety switch u
Prevents the tool from being switched on accidentally
- switch on tool by first pressing safety switch A and then
pulling trigger switch B
- switch off tool by releasing trigger switch B
! after switching off the tool the blade continues to
rotate for a few seconds
Operating instructions
- hold the mower with both hands
- place the mower on the edge of the lawn and mow in a
forward direction
- reverse at the end of each turn, slightly overlapping the
previous cut strip
! only use the mower on dry grass
- keep the mower away from solid objects and plants
! for mowing long grass, first set the cutting
mechanism to the maximum cutting height, then
to a lower cutting height
! adjust your walking pace when mowing long grass
Grass box full indicator i
- empty grass box H as soon as flap J lowers by itself,
indicating that the grass box is full
- for optimal grass collecting performance regularly clean
the holes underneath flap J with a hand brush
MAINTENANCE / SERVICE
This tool is not intended for professional use
Always switch off the tool, remove battery pack, and
ensure that all moving parts have come to a complete
standstill
Always keep tool clean
Clean the mower after each use with a hand brush and
a soft cloth
! do not use water (especially no high-pressure
sprays)
- remove compacted grass cuttings from the blade area
with a wooden or plastic implement
Storage o
- for saving substantial storage space fold the tool
handle and store the tool as illustrated; empty grass
box first
! ensure that the handle cord is not trapped when
folding/unfolding the tool handle (do not drop the
handle)
- do not place other objects on top of the mower when
stored
Regularly check the grass box for wear or damage
Regularly check for worn or damaged blades and bolts
and have them replaced in sets to preserve balance
12

Publicité

loading