Memorising The Keygo Io Remote Controls; Memorising The Keytis Io Remote Controls - SOMFY Control Box 3S io Manuel D'installation

EN
8.1.3. Meaning of displayed codes
Code
Add Successful memorisation of a unidirectional remote control
- - - Successful memorisation of a bidirectional remote control
dEL Delete a previously memorised button
rEF Unsuccessful memorisation of a bidirectional remote control
FuL Memory full (only for unidirectional remote controls)

8.2. Memorising the Keygo io remote controls

8.2.1. Memorising via the programming interface
Complete opening control - Fig. 20
Pedestrian opening control - Fig. 21
Lighting control - Fig. 22
Auxiliary output control (P15 = 4, 5 or 6) - Fig. 23
8.2.2. Memorising by copying a previously memorised
Keygo io remote control - Fig. 24
This operation is used to copy the programming from a previously memo-
rised remote control button.
1) Press the outer le and right buttons on the previously memorised
remote control together until the green indicator light flashes (2 s).
2) Press and hold the button to be copied on the previously memorised
remote control for 2 seconds.
3) Briefly press the outer le and right buttons on the new remote control
together.
4) Briefly press the selected button to actuate the motorisation on the
new remote control.

8.3. Memorising the Keytis io remote controls

Attention
The Keytis io remote control system key memorising and copy
memorising operations can only be carried out at the installation
site. To obtain authorisation to transfer its system key or program-
ming, the previously memorised remote control must be able to
establish radio communication with a receiver on the installation.
If the installation already includes other io-homecontrol® products
with at least one memorised bidirectional remote control, the
Keytis io remote control must first memorise the system key (see
below).
A previously memorised button cannot be memorised on a second receiv-
er. To find out whether a button has already been memorised, press it:
• button already memorised → green indicator light comes on.
• button not memorised → orange indicator light comes on.
To clear a previously memorised button, refer to the section entitled Clear-
ing individual buttons on the Keytis io remote control.
8.3.1. Memorising the system key - Fig. 25
Attention
This step must be performed if the installation already includes
other io-homecontrol® products with at least one memorised
bidirectional remote control.
If the Keytis io remote control to be memorised is the first remote
control on the system, go directly to the "Memorising the Keytis io
remote control" step.
1) Setting the memorised remote control to key transfer mode:
- Keytis io, Telis io, Impresario io, Composio io remote controls:
press the "KEY" button until the green indicator light comes on
(2 s).
- Other remote control: refer to the instructions.
2) Briefly press the "KEY" button on the new remote control. Wait for the
confirmation beep (a few seconds).
9
Description
8.3.2. Memorising via the programming interface
If the installation already includes other io-homecontrol® products with
at least one memorised bidirectional remote control, the Keytis io remote
control must first memorise the system key (see page 16).
Complete opening control - Fig. 26
PEDESTRIAN opening control - Fig. 27
LIGHTING control - Fig. 28
AUXILIARY OUTPUT control (P15 = 4, 5 or 6) - Fig. 29
8.3.3. Memorising by copying a previously memorised
Keytis io remote control
Complete copying of a Keytis io remote control - Fig. 30
This operation is used to copy all the buttons on a previously memorised
remote control.
The new remote control must not be memorised for another automatic
control system.
Ensure that the new remote control has memorised the system key.
1) Press the "PROG" button on the memorised remote control until the
green indicator light comes on (2 s).
2) Press briefly on the "PROG" button of the new remote control. Wait
for the second beep and for the green light to flash quickly (a few
seconds).
Copying individual buttons on a Keytis io remote control - Fig. 31
This operation is used to copy the memorisation of a single button on a
previously memorised remote control to a blank button on a new remote
control.
Ensure that the new remote control has memorised the system key.
1) Press the "PROG" button on the memorised remote control until the
green indicator light comes on (2 s).
2) Briefly press the button to be copied on the previously memorised re-
mote control.
3) Briefly press the "PROG" button on the new remote control.
Wait for the confirmation beep (a few seconds).
4) Briefly press the selected button to actuate the motor on the new re-
mote control.
Attention
It is not possible to memorise Keytis io remote controls in the
following cases:
• The remote control has not memorised the system key.
• Several of the installation's receivers are in programming mode.
• Several remote controls are in key transfer or memorisation
mode.
Incorrect memorisation is indicated by a rapid series of beeps
accompanied by a flashing orange indicator light on the Keytis
remote control.
CONTROL BOX 3S io
Copyright © 2017 SOMFY ACTIVITES SA. All rights reserved.