Using The Control Panel - Whirlpool ACP092PR0 Guide D'utilisation Et D'entretien

Display Symbols
A
B
C
D
E
A. Remote control signal D. Dry mode indicator
transmit indicator light
™
B. ComfortMode control E. Fan only mode
indicator light
C. Cooling mode F. Auto fan speed
indicator light
NOTES:
The air conditioner display shows the current room
temperature and 24-hour clock.
In the event of a power failure, your air conditioner will
operate at the previous settings when the power is restored.
When changing modes while air conditioner is operating, the
compressor will stop for 3 to 5 minutes before restarting. If a
button is pressed during this time, the compressor will not
restart for another 3 to 5 minutes.
In Cooling or Dry mode, the compressor and fan will stop
when room temperature reaches set temperature.
Mode
Press MODE to choose ComfortMode
Fan Only.
Cooling Mode
This mode cools the room. Temperature and fan speed are set by
the user.
1. Press MODE to choose Cooling.
2. Choose fan speed. See "Fan Speed."
3. Choose temperature. See "Temperature."
4. Press POWER to start the air conditioner. The RUN indicator
light will glow green.
5. When WATER FULL indicator light glows red, air conditioner
will turn off automatically. See "Portable Air Conditioner Care"
for directions on draining the air conditioner.
Dry Mode
Dries the room. Temperature is set by user. Fan runs on Low only.
NOTES:
Dry mode should not be used to cool the room.
Dry mode does not require hot air outlet hose.
1. Press MODE to choose Dry.
2. Choose temperature. See "Temperature."

Using the Control Panel

F
G
H
I
G. High fan speed
light indicator light
H. Low fan speed
indicator light indicator light
I. Display set
indicator light temperature
™
control, Cooling, Dry or
3. Press POWER to start the air conditioner. The RUN indicator
light will glow green.
4. When WATER FULL indicator light glows red, air conditioner
will turn off automatically. See "Portable Air Conditioner Care"
for directions on draining the air conditioner.
NOTES:
Press the minus button once to decrease the set temperature
by 2ºF (1ºC), or press twice to decrease set temperature by
4ºF (2ºC).
Press the plus button once to increase the set temperature by
2ºF (1ºC), or press twice to increase set temperature by 4ºF
(2ºC).
ComfortMode ™ Control
Air conditioner automatically selects cool or dry depending on
room temperature. When in Dry mode, air conditioner
automatically selects fan speed and temperature. When in
Cooling mode, air conditioner automatically selects temperature,
but fan speed may be selected by user.
1. Press MODE to choose ComfortMode control. Compressor
and fan will start automatically based on room temperature.
RUN indicator light will glow green, and air swing will start.
2. During Cooling mode, fan speed may be changed. See "Fan
Speed."
3. When WATER FULL indicator light glows red, air conditioner
will turn off automatically. See "Portable Air Conditioner Care"
for directions on draining the air conditioner.
NOTES:
Press the minus button once to decrease the set temperature
by 2ºF (1ºC), or press twice to decrease set temperature by
4ºF (2ºC).
Press the plus button once to increase the set temperature by
2ºF (1ºC), or press twice to increase set temperature by 4ºF
(2ºC).
Fan Only Mode
Serves only to move air. Fan speed is set by user.
1. Press MODE to choose Fan Only.
2. Choose fan speed. See "Fan Speed."
3. Press POWER to start the air conditioner. The RUN indicator
light will glow green.
Fan Speed
1. Press FAN to set the fan speed.
2. Choose Auto, High or Low.
Auto—Fan speed set automatically
High—Maximum cooling
Low—Minimum cooling
NOTE: Press and hold FAN SPEED for 3 seconds to change
vertical airflow direction. Press and hold FAN SPEED for
3 seconds again to stop airflow louver at desired airflow
direction.
7