RIB JOY 40 SS Mode D'emploi page 5

Step 6 - Insert the motor into the tube, with the crown (2) opposite an opening of roller tube.
Step 7 - For the complete assembly, insert one side of tube into the idler bracket (9), and insert the other side into the motor bracket (1).
3.3 Electrical connection (Fig. 12 - 13)
Warning!
When the blue and brown wires are powered, the adapter rotates clockwise.
When the blue and black wires are powered, the adapter rotates counterclockwise.
The yellow / green wire is that top connect to the electric ground.
NOTE: to discriminate the rotating direction of the driving adapter, please refer to the Cap. 4: "Debugging method"".
4. DEBUGGING METHOD
4.1 Adjusting instruction
· It is possible to perform a preventive control of the operator by holding it in yoour hand and giving power to the motor. Operate the switch to power the blue and black (or brown) wires. The
adapter starts rotating counterclockwise (or clockwise).
· Simultaneously turn the crown at the same speed and in the same direction of rotation as the adapter until it stops. Turn the crown back to allow the adapter to move back to the starting
position.
· Repeat the above operations until the adapter stops and the direction of rotation is not established definitively.
· Swap the electrical connections (black and brown wires) if you want to change the direction of rotation.
· If a mark has already been applied outside the crown, the number of laps can be considered the stroke of the operator (the number of laps set at the factory is 5).
· When the rotation of the adapter is interrupted by the limit switch, the crown is not allowed to move again to prevent damage to the affected machine parts.
· If the number of revolutions of the adapter must be changed, it is possible to do so by observing the signs and colors of the limit switch adjustment screws, where "+" symbolizes the increase
in revolutions and "-" is going to decrease; black indicates counterclockwise while red clockwise. The regulation should take place when the motor has been installed on the roller shutter.
· Before installation, the user can establish a number of revolutions that may be lower than the practical operating requirements.
· Fix the limit switch in one direction and proceed with the adjustment of the limit switch only in the opposite direction. The opening direction should be the same as the initial operating direction
after installation. If, for example, the initial operating direction is anti-clockwise after installation, fix the limit switch of the clockwise rotation direction before installation and gradually adjust
that of the counter-clockwise direction.
4.2 Stroke adjusting method (Fig. 14)
When you want to increase or decrease the stroke of the engine in the clockwise direction, turn the red screw, while to adjust the stroke of the operator in the anticlockwise direction, turn the
white screw.
To indicate the increase or decrease of the path length "+" stands for increase and "-" for decrease.
NOTE: The direction of travel adjustment may be different if the motor is installed with the inverted electric cables or on the opposite side of the side pipe. Carefully check the signs of the
directions of movement during adjustments.
5. OTHER ATTENTIONS AND NOTES
· Do not store the motor with strong acid and alkali or dirty & eroding materials.
· Do not use the motor in humid or damp environments.
· Do not start the motor frequently or overload it as it might reduce its operation life.
· Do not turn the limit switches screws or the crown when the operator has not yet been installed.
· If you wish to open the shutters under power-off circumstance, you may choose the MS series products which carries manual functions, and do not forget to invite professionals to install the
handling bar and locks. And please note that the manual function doesn't work in the power-on condition.
· Do not connect in parallel motors with mechanical limit stops: the parallel connection originates phase return paths, caused by the capacitors present inside motor that damage the limit
stops. Use specific control panels.
· The electric wiring must comply with the prevailing CEI standards. Motors using cables: PVC H05- VVF and rubber H05- RRF must be installed indoors. For every centralisation or for motors
control from different points, check the indications on the official catalogue.
· Do not power motors with voltages other than 230V: overvoltage may cause damages resulting in wrong operation or in the loss of the stop points; undervoltage may cause a wrong
development of the declared torque and not result in the opening/closing of shutters or blinds.
· If a single non-centralised control is used for each single motor, use a synchronous connection with interlocked buttons, such as Biticino 502N
· Generic centralisations making use of relays cannot be made.
· Do not simultaneously send up and down movement controls on the same operator.
· Avoid commands with switching times between ascent and descent of less than 1 second.
6. PROBLEM RESOLUTION
Problem
Pressing the down button the shutter rises.
The driving adapter can only rotate in one direction when
the operator is powered.
In the presence of power supply, the motor refuses to
operate or starts slowly.
The motor has stopped suddenly
The engine stops working and the stroke length can not
be increased.
Unexpected noises are emitted during the rotation of the
shutter
Possible cause
Connection exchanged between the V-W wires
The limit switch of the opposite direction must be
set.
Voltage too low
Errors in line connection
Overload
Installation errors
Operating time (4min) has been exceeded
The stroke has been adjusted to maximum.
Roller too long that causes friction between the
shutter and the support brackets
Solution
Swap the brown and black wires together
Turn the crown in the direction of rotation of the driving adapter
Regulate the voltage to the rated
Check the wires and correct it
Install the correct operator for the applied load.
Reinstall the engine
After about 20 minutes the engine will cool down and restart automatically.
Remove the motor from the roller and turn the crown in the opposite direction
for many laps (depending on practical needs). Then put it in the roller and
adjust the end position.
If the pulley is flexible, it is possible to cut a part of the tube with a saw to
reduce the friction between the support brackets and the roller