Ergomotion e Serie Manuel Du Propriétaire page 4

safety precautions and usage statements
continuously for more than [2] minutes in an [18] minute time
period or approximately 10% duty cycle . Attempting to circum-
vent or exceed this rating will shorten the life expectancy of
the product and may void the warranty .
Weight Limits: This product is not rated to support weights
exceeding 750 pounds (340kg) . This product is not rated
to support weights in excess of 750 pounds inclusive of the
mattress and bedding . The base will structurally support this
weight, provided it is evenly distributed across the bed base .
The adjustable base is not designed to support or lift this
amount in the head or foot sections alone . Exceeding this
weight restriction could damage the bed and/or cause injury
and will void the warranty .
Acoustics: The massage function will emit a noticeable tone
during operation . As the massage intensity level is increased,
the tone will intensify . The volume of this tone is directly
related to the location environment . For example, when
demonstrated in a show room, the surrounding environmen-
tal noise will cover some of the massage noise . However,
when installed in a home setting with wooden floors, car-
peted or not, the massage volume will be more noticeable .
In normal base operation, the wheels which allow the bed to
maintain its distance from the wall, will make contact with
the steel platform supports of the base creating a contact
noise . When entering, exiting or shifting weight on the base,
this contact noise may be audible as the wheels make con-
tact . This is normal .
Fabric Care: To prolong the life of your fabric, protect from
direct sunlight whenever possible . For spot cleaning, wipe
area with a light damp sponge or vacuum with a soft brush
attachment to remove particles . Keep at a minimum of 30cm
(12 inches) away from direct heat sources .
For deeper cleaning, blot liquid spills with a clean dry cloth .
Wipe with a clean cloth dampened with warm water . Do not
wet excessively. A soft bristle brush may be used to remove
ingrained soil . Avoid scratching by gentle brushing . Wipe with
a clean cloth dampened with warm water to remove residues .
Dry in shade away from direct heat .
If persistent marks remain visible after cleaning, seek
professional advice .
Tolerance: All Ergomotion adjustable foundations, depending
on make and model, are designed and manufactured to
perform and function within designated quality control
parameters . Bases are subject to meticulous and rigorous
inspections during the quality control process to ensure
bases will operate within these standards during normal
operating use . Normal operating use is defined as the
following: Adjustable foundation is to be operated with
a mattress and load . Testing procedures require lifetime
cycle tests with up to 120kg distributed load . The angle
2
(designated "α" in figure 1) between the back section and the
flat section for various configurations of the mattress support
platform shall be ± 3°, which translates to a tolerance of up
to 1 ½" .
The angle (designated "β" in figure 1) between the flat
section and foot section for various configurations of the
mattress support platform shall be ± 3°, which translates to a
tolerance of up to ¾" .
Any adjustable foundation deemed to be within these
allocated tolerances is considered to have met the
All Ergomotion adjustable foundations, depending on make and model, are designed and manufactured to perform and
function within designated quality control parameters. Bases are subject to meticulous and rigorous inspections during
the quality control process to ensure bases will operate within these standards during normal operating use.
manufacturer's quality control standards .
Normal operating use is defined as the following:
-Adjustable foundation is to be operated with a mattress and load. Testing procedures require lifetime cycle
tests with up to 120kg distributed load.
The angle (designated "α" in figure 1) between the back section and the flat section for various configurations of the
mattress support platform shall be ± 3°, which translates to a tolerance of up to 1 ½".
The angle (designated "β" in figure 1) between the flat section and foot section for various configurations of the mattress
support platform shall be ± 3°, which translates to a tolerance of up to ¾".
When operating a "paired" split base setup there may be a time latency up to 1.5 seconds between each bases articulation.
Any adjustable foundation deemed to be within these allocated tolerances is considered to have met the manufacturer's
quality control standards.
Blake Pettit
Quality Assurance Manager
Ph 805-979-3875
Fx 805-979-9399
www.ergomotion.com
Ergomotion Inc. | ph 1-888-550-3746 | fx 805-979-9399 | www.ergomotion.com
FCC Compliance:
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
Adjustable
Bed Tolerance
(α°)
(β°)