Technical Data; Unpacking; Installation - Scheppach COS125-20ProS Traduction Des Instructions D'origine

• The battery can be damaged by pointed ob-
jects such as nails or screwdrivers or by force
applied externally. An internal short circuit may
occur, causing the battery to burn, smoke, explode
or overheat.
• Only use the battery with products from the
manufacturer. This is the only way in which you
can protect the battery against dangerous over-
load.
• Protect the battery against heat, e.g. against
continuous intense sunlight, fire, water, and
moisture. There is a risk of explosion.
Information on the rechargeable battery
Please observe the operating manual for the re-
chargeable batteries.
Information on the charging unit and charging
process
Please observe the operating manual for the charg-
ing unit.
Warning! This electric tool generates an electro-
magnetic field during operation. This field can im-
pair active or passive medical implants under certain
conditions. In order to prevent the risk of serious
or deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool
Residual risks
The machine has been built according to the state of
the art and the recognised technical safety require-
ments. However, individual residual risks can arise
during operation.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
• Residual risks can be minimised if the „safety in-
structions" and the „Proper use" are observed
along with the whole of the operating instructions.
• Avoid accidental starting of the machine.
• Use the tool that is recommended in this manual..
This ensures that your machine performs optimally.
• Hands may never enter the processing zone when
the machine is in operation.

6. Technical data

Motor power supply:
Rated speed:
Size of paper. :
Weight
Subject to technical changes!
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Noise and vibration
m Warning: Noise at the workplace can exceed 85
dB (A). In this case, noise protection measures are
necessary for the user (wear hearing protection!).
Noise output in dB
sound power level L
sound pressure level L
uncertainty K
Vibration value
Vibration a
Uncertainty K

7. Unpacking

• Open the packaging and remove the device care-
• Remove the packaging material as well as the
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
• If possible, store the packaging until the warranty
• Familiarize yourself with the machine with the help
• Use only original parts for accessories as well as
• Please quote our article numbers as well as type
m ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!

8. Installation

m IMPORTANT!
You must fully assemble the appliance before
using it for the first time!
To ensure that the Li battery pack provides long ser-
vice you should take care to recharge it promptly.
You must recharge the battery pack when you notice
20 V
that the power of the cordless equipment drops.
10000 min
-1
Ø 125 mm
Caution! Make sure that the device is switched off
1,1 kg
before you connect it to the mains supply.
Note! Always switch on the delta sander before
bringing it into contact with the workpiece material.
87 dB(A) (EN ISO 3744)
WA
76 dB(A) (EN ISO 11201)
pA
3 dB(A)
wa/pA
9,5 m/s²
h
1,5 m/s²
h
fully.
packaging and transport bracing (if available).
port damage. Inform the transport agent imme-
diately of any faults. Later complaints cannot be
considered.
period has expired.
of the operating instructions manual before using
it.
consumables and spare parts. Spare parts can be
obtained from your retailer.
and production year in all your orders.
GB 19