Scheppach HC100dc Traduction Des Instructions D'origine page 19

- Do not use any electric tool on which the switch
cannot be switched on and off.
15. Have your electric tool repaired by a qualified
electrician
- This electric tool conforms to the applicable safe-
ty regulations. Repairs may only be performed by
an electrician using original spare parts. Other-
wise accidents can occur.
16. Important!
- For your own safety you must only use the acces-
sories and additional units listed in the operating
instructions or recommended or specified by the
manufacturer. The use of mounted tools or ac-
cessories other than those recommended in the
operating instructions or catalogue may place
your personal safety at risk.
17. Noise
- Wear ear muffs when you use the compressor.
18. Replacing the power cable
- To prevent hazards, leave the replacement of
damaged power cables strictly to the manufac-
turer or a qualified electrician. There is a risk of
electric shock!
19. Inflating tires
- Directly after inflating tires, check the pressure
with a suitable pressure gauge, for example at
your filling station.
20. Roadworthy compressors for building site opera-
tions
- Make sure that all lines and fittings are suitable
for the maximum permissible operating pressure
of the compressor.
21. Place of installation
- Set up the compressor on an even surface.
22. Supply hoses at pressures above 7 bar should be
equipped with a safety cable (e.g. a wire rope).
23. Avoid over-stressing the piping system by using
flexible hose connections to prevent kinking.
24. Use a residual current circuit breaker with a trig-
ger current of 30 mA or less. Using a residual cur-
rent circuit breaker reduces the risk of an electric
shock.
m WARNING! This electric tool generates an elec-
tromagnetic field during operation. This field can im-
pair active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.
ADDITIONAL SAFETY INSTRUCTIONS
Observe the corresponding operating manuals
of the respective compressed air tools / com-
pressed air attachments! The following general
warnings must also be observed.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Safety instructions for working with compressed
air and blasting guns
• Ensure there is sufficient distance to the product,
at least 2.50 m, and keep the compressed air tools
/ compressed air attachments away from the com-
pressor during operation.
• The compressor pump and lines can become
very hot during operation. Touching these parts
will burn you.
• The air which is sucked in by the compressor must
be kept free of impurities that could cause fires or
explosions in the compressor pump.
• When releasing the hose coupling, hold the hose
coupling piece with your hand. This way, you can
protect yourself against injury from the rebound-
ing hose.
• Wear safety goggles and a respirator when work-
ing with the compressed air pistol. Dusts are harm-
ful to health! Injuries can be easily caused by for-
eign objects and blown away parts.
• Do not blow at people with the blow-out pistol and
do not clean clothes while being worn. Risk of in-
jury!
Safety instructions when using spraying attach-
ments (e.g. paint sprayers)
• Keep the spray attachment away from the com-
pressor when filling so that no liquid comes into
contact with the compressor.
• Never spray in the direction of the compressor
when using the spraying attachments (e.g. paint
sprayers). Moisture can lead to electrical hazards!
• Do not process any paints or solvents with a fl ash
point below 55 °C. Risk of explosion!
• Do not heat up paints or solvents. Risk of explo-
sion!
• If hazardous liquids are processed, wear protective
filter units (face guards). Also, adhere to the safety
information provided by the manufacturers of such
liquids.
• The details and designations of the Ordinance on
Hazardous Substances, which are displayed on the
outer packaging of the processed material, must be
observed. Additional protective measures are to be
undertaken if necessary, particularly the wearing of
suitable clothing and masks.
• Do not smoke during the spraying process and/or
in the work area. Risk of explosion! Paint vapours
are easily combustible.
• Never set up or operate the equipment in the vicin-
ity of a fire place, open lights or sparking machines.
• Do not store or eat food and drink in the work area.
Paint vapours are harmful to your health.
• The work area must exceed 30 m³ and suffi cient
ventilation must be ensured during spraying and
drying.
GB | 19