STEINEL PROFESSIONAL RS PRO LED B1 Notlich Mode D'emploi page 7

Diese Herstellergarantie lässt Ihre gesetzlichen
Rechte unberührt. Die hier beschriebenen Leistun-
gen gelten zusätzlich zu den gesetzlichen Rechten
und beschränken oder ersetzen diese nicht.
Die Garantie gilt für sämtliche STEINEL-Produkte,
die in Deutschland gekauft und verwendet werden.
Es gilt deutsches Recht unter Ausschluss des
Übereinkommens der Vereinten Nationen über
Verträge über den internationalen Warenkauf (CISG).
Geltendmachung
Wenn Sie Ihr Produkt reklamieren wollen, senden Sie
es bitte vollständig und frachtfrei mit dem Original-
Kaufbeleg, der die Angabe des Kaufdatums und der
Produktbezeichnung enthalten muss, an Ihren
Händler oder direkt an uns, die STEINEL Vertrieb
GmbH - Reklamationsabteilung -, Dieselstraße 80-84,
33442 Herzebrock-Clarholz. Wir empfehlen Ihnen
daher, Ihren Kaufbeleg bis zum Ablauf der Garantie-
zeit sorgfältig aufzubewahren.
Für Transportkosten und -risiken im Rahmen der
Rücksendung übernehmen wir keine Haftung.
E U
5
3
J A H R
HERSTELLER HERSTELLER HERSTELLER
GARANTIE GARANTIE GARANTIE
GB
1. About this document
Please read carefully and keep in a safe place.
– Under copyright. Reproduction either in whole or
in part only with our consent.
– Subject to change in the interest of technical
progress.
Symbols
Warning of electrical hazard.
!
Hazard warning!
Reference to other information in the
document.
...
...
2. General safety precautions
Disconnect the power supply before
attempting any work on the unit.
Working with electrical current may produce
hazardous situations. Touching live parts can result
in electrical shock, burns or death.
• Always follow the safety precautions and instruc-
tions given in this document. ...
- Work on mains voltage must only be performed
by qualified, skilled personnel.
- National wiring regulations and electrical
operating conditions must be observed
(e.g. DE-VDE 100, AT-ÖVE-ÖNORM E8001-1,
CH-SEV 1000).
- The luminaire must not be installed in poten-
tially explosive atmospheres.
- During installation, the electric power cable be-
ing connected must be dead and remain dead.
- The light must be protected by a circuit breaker
(10 A).
- Connection to a dimmer will damage the
luminaire.
- No more than twenty RS PRO LED B1
luminaires must be connected in series.
- Do not coat or stick adhesive film to the
luminaire.
- Select a non-vibrating site of installation to
ensure proper working order.
– 12 –
...
Hazard from LED light!
Looking directly into the LED light when it is ON
could damage your retina.
• Never look into the LED luminaire at short range
or for any prolonged period (> 5 minutes).
– The luminaire must not be installed in potentially
explosive atmospheres.
– Select a non-vibrating site of installation to en-
sure proper working order.
– No changes or modifications must be made to
the product.
!
Hazard from vapours or electrolyte fluid!
Vapours or electrolyte fluid may escape from the
rechargeable battery if it is damaged or used im-
properly. Coming into contact with them may result
in severe injury (e.g. loss of sight, acid burns).
• Never open the rechargeable battery enclosure
or the rechargeable battery itself.
• Do not allow vapours or electrolyte fluid to come
into contact with your eyes. In the event of con-
tact with eyes:
– Do not rub your eyes.
– Immediately rinse eyes with plenty of clean
water (such as tap water).
– Seek medical advice.
• Do not touch any electrolyte fluid that has
escaped.
• Immediately move product away from naked
flamed or sources of heat.
• Immediately remove contaminated clothing.
3. RS PRO LED B1 emergency light
Proper use
– Luminaire with emergency lighting function.
– Sensor-switched indoor LED light with integrated
back-up rechargeable battery that automatically
provides 3 hours of LED emergency lighting in
compliance with EN 60598-2-22.
– Efficient, automatically controlled luminaire with
high-frequency sensor for detecting persons.
– Photoelectric sensor for identifying the room
situation.
Package contents / product features (Fig. 3.1)
Product dimensions (Fig. 3.2)
A Shade
B HF-sensor
C Emergency light test button
D Red LED
E Plug-in terminal
F Sealing plug
G Wall / ceiling mount
H Light-level setting
I Time setting
J Reach setting
K PE
L Chassis
M Sealing plug
N Shrouds for partially limiting range
O Emergency-light module
P Rechargeable batteries
Q Spacer for surface wiring
Storage / transportation
The emergency light module and luminaire should
be stored and transported separately from each
other. Requiring no connection to mains power, the
emergency light module is immediately ready for
operation and switches ON when it is plugged into
the luminaire. The emergency light module has no
OFF switch. This means means it should only be
installed more or less immediately before use.
– 13 –