STEINEL PROFESSIONAL RS PRO LED B1 Notlich Mode D'emploi page 9

• Reach setting (sensitivity)
(Fig. 5.5). Factory setting: +
- Reach is understood to mean the diameter of
the more or less circular detection zone pro-
duced on the floor when mounting the sensor
at a height of 2.5 m.
- Control dial set to (–) = just before (–) minimum
reach (Ø approx. 1m)
- Control dial set to (+) = maximum reach
(Ø approx. 8 m)
- Reach can be reduced in 4 directions by fitting
the shrouds included with the luminaire
(Fig. 7.2 - 7.6).
6. Connection options
– Normal connection without switch, several
RS PRO LED B1 operating in parallel (Fig. 6.1)
– Normal connection with switch (Fig. 6.2)
– Normal connection with other loads connected,
e.g. fan, other types of luminaire (Fig. 6.3)
7. Limiting reach
– Reach can be limited in 4 directions by fitting
shrouds (Fig. 7.2 – 7.6)
8. Sensor-switched light malfunctions
Sensor-switched light without power
– Fuse has tripped, not switched ON, break in wiring
• Activate, change fuse, turn ON mains switch,
check wiring with voltage tester
– Short circuit in mains power supply lead
• Check connections
– Any mains switch OFF
• Switch on at mains switch
Sensor-switched light does not switch ON
– Wrong twilight setting selected
• Readjust
– Mains switch OFF
• Switch ON
– Building fuse faulty
• Activate, change fuse, check connection if
necessary
Light does not switch OFF
– Continued movement within the detection zone
• Check detection zone
Sensor-switched light switching ON despite no
movement being detected
– Install luminaire at a non-vibrating site
• Securely mount enclosure
– Movement occurred but not detected by the
observer (movement behind wall, small object
moving in immediate proximity of lamp etc.)
• Check detection zone
Sensor-switched light does not switch ON
despite movement taking place
– To minimise malfunctioning, rapid movements
are suppressed or detection zone set too small
• Check detection zone
9. Emergency light module malfunctions
Red LED charge indicator not showing
– Emergency light module not properly engaged
• Check mains power connection
• Make sure all rechargeable batteries are fitted
and inserted the right way round
Red LED charge indicator ON, emergency light
LEDs do not switch ON in response to pressing
button
– Rechargeable batteries very low
– Rechargeable battery cell faulty or fitted the
wrong way round
• Check mains power connection
• Make sure rechargeable batteries are fitted the
right way round and check state of charge
Red LED charge indicator OFF. On pressing
button, switches ON together with emergency
light LED
• Make sure all rechargeable batteries are fitted
and inserted the right way round
Emergency light LEDs immediately go out on
pressing button
– Rechargeable batteries run out or faulty
• Check emergency light module's mains power
connection, red LED charge indicator must
show
10. Accessories (optional)
– Emergency light module without rechargeable
batteries EAN 4007841006440
– Replacement rechargeable battery emergency
light module (3 each) EAN 4007841006457
– 16 –
11� Declaration of Conformity
STEINEL Vertrieb GmbH hereby declares that the
RS PRO LED B1 radio equipment type conforms
to Directive 2014/53/EU. The full wording of the EU
Declaration of Conformity is available for download-
ing from the following Internet address: http://www.
steinel.de
12� Disposal
Electrical and electronic equipment, accessories and
packaging must be recycled in an environmentally
compatible manner.
Do not dispose of electrical and electronic
equipment as domestic waste.
EU countries only:
Under the current European Directive on Waste
Electrical and Electronic Equipment and its imple-
mentation in national law, electrical and electronic
equipment no longer suitable for use must be col-
lected separately and recycled in an environmentally
compatible manner.
Do not throw devices, rechargeable
batteries / batteries into household waste,
fire or water at the end of their useful life.
Rechargeable batteries / batteries should be col-
lected, recycled or disposed of in an environmentally
friendly manner.
EU countries only:
In accordance with Directive 2006/66/EC, defective
or spent rechargeable batteries / batteries must be
recycled. Waste rechargeable / non-rechargeable
batteries can be returned to the point of purchase or
to a collection facility for hazardous substances.
13. Manufacturer's Warranty
As purchaser, you are entitled to your statutory
rights against the vendor. If these rights exist in
your country, they are neither curtailed nor re-
stricted by our Warranty Declaration. We guarantee
that your STEINEL Professional sensor product
will remain in perfect condition and proper working
order for a period of 5 years. We guarantee that
this product is free from material-, manufacturing-
and design flaws. In addition, we guarantee that all
electronic components and cables function in the
proper manner and that all materials used and their
surfaces are without defects.
Making Claims
If you wish to make a claim, please send your prod-
uct complete and carriage paid with the original
receipt of purchase, which must show the date of
purchase and product designation, either to your
retailer or contact us at STEINEL (UK) Limited,
25 Manasty Road, Axis Park, Orton Southgate,
Peterborough, PE2 6UP, for a returns number. For
this reason, we recommend that you keep your re-
ceipt of purchase in a safe place until the warranty
period expires. STEINEL shall assume no liability for
the costs or risks involved in returning a product.
For information on making claims under the terms
of the warranty, please go to www.steinel-profes-
sional.de/garantie
If you have a warranty claim or would like to ask
any question regarding your product, you are wel-
come to call us at any time on our Service Hotline
G B
01733 366700.
5
1 3
Y E A R Y E A R
MANUFACTURER'S MANUFACTURER'S
WARRANTY WARRANTY
– 17 –
Y E A R
MANUFACTURER'S
WARRANTY