Beninca JM.3 Mode D'emploi page 11

Manufacturer: Automatismi Benincà SpA.
Address: Via Capitello, 45 - 36066 Sandrigo (VI) - Italia
Herewith declares that: the pulling automatic system for sectional doors model JM.3/JM.4.
• is intended to be incorpored into machinery or to be assembled with other machinery to constitute machinery covered by
Directive 89/392 EEC, as amended;
• does therefore not in every respect comply with the provisions of this Directive;
• does comply with the provisions of the following other EEC Directives:
Direttiva bassa tensione 73/23/CEE, 93/68/CEE.
Direttiva compatibilità elettromagnetica 89/336/CEE, 93/68/CEE.
and that:
• the following (parts/clauses of) harmonized standards have been applied:
EN 55022, EN 61000-3-2, EN 61000-3-3, EN 50082-1, EN 60335-1.
and furthermore declares that it is not allowed to put the machinery into service until the machinery into which it is to be incorporated or of which it
is to be a component has been found and declared to be in conformity with the provisions of Directive 89/392/EEC and with national implementing
legislation, i.e. as a whole, including the machinery referred to in this declaration.
Benincà Luigi, Responsabile legale.
Sandrigo, 10/02/2007.
WARNING
The product shall not be used for purposes or in ways other than
those for which the product is intended for and as described in this
manual. Incorrect uses can damage the product and cause injuries
and damages.
The company shall not be deemed responsible for the non-compliance
with a good manufacture technique of gates as well as for any defor-
mation, which might occur during use.
Keep this manual for further use.
Qualified personnel, in compliance with regulations in force, shall
install the system.
Packaging must be kept out of reach of children, as it can be hazardous.
For disposal, packaging must be divided the various types of waste (e.g.
carton board, polystyrene) in compliance with regulations in force.
The installer must supply all information on the automatic, manual and
Introduction
Thank you for choosing our JM.3/JM.4 ratiomotor.
All items in the wide Benincà production range are the result of
twenty-years' experience in the automatism sector and of continu-
ous research for new materials and advanced technologies.
We are, therefore, in the position to offer highly reliable products
that due to their power, effectiveness and useful life, fully satisfy
the final user's requirements.
All our products are covered by warranty.
Possible injury to people or accidents caused by defects in con-
struction are covered by a civil liability policy drawn up with one of
the major insurance companies.
1. General information
The system has been studied to motorize sectional doors.
To be applied onto balancing doors, a special fitting arm is required
(item AU.C25).
In any case, following conditions will have to be observed:
- the distance between the door highest point and the ceiling must
be at least 40mm (fig. 2).
- it has to be possible to open and close the door by pulling and
pushing horizontally its top edge (fig.2).
- manual moves must be smooth and regular.
The gear motor is available in two versions:
JM.3 (600Nm) and JM.4 (1200Nm) to which the following tracks
can be matched (fig.1):
PTC.3: Pre-assembled track, with 8 mm belt, 2.5m max height,
Declaration by the manufacturer
(Directive 89/392/EEC, Art. 4.2 and Annex II, sub B) - No servicing
emergency operation of the automatic system and supply the end user
with instructions for use.
An omnipolar switch/section switch with remote contact opening equal
to, or higher than 3mm must be provided on the power supply mains..
Make sure that before wiring an adequate differential switch and an
overcurrent protection is provided.
Pursuant to safety regulations in force, some types of installation require
that the gate connection be earthed.
During installation, maintenance and repair, cut off power supply before
accessing to live parts.
Descriptions and figures in this manual are not binding. While leaving
the essential characteristics of the product unchanged, the manufac-
turer reserves the right to modify the same under the technical, design
or commercial point of view without necessarily update this manual.
for JM.3 only
PTC.4: Pre-assembled track, with 10 mm belt, for doors with 2.5
m max height, for JM.3 and JM.4
PTC.L4: Pre-assembled track, with 10mm belt, for doors with 3.5
m max height, for JM.3 and JM.4
Technical data
Feed
Motor feed
Consumption
Drive speed
Drive/thrust force
Degree of protection
Jogging
Operating temp.
Noise level
Max. door height:
with PTC3/PTC4
with PTCL4
Power unit weight
Total weight:
with PTC3/PTC4
with PTCL4
JM.3 JM.4
230Vac
230Vac
24Vdc 24Vdc
0,7 A 1,5 A
8,9 m/1' 8,9 m/1'
600N 1200N
IP40 IP40
intensive use intensive use
-20°C/+50°C -20°C/+50°C
<70dB (A) <70dB (A)
2,5m 2,5m
3,5m 3,5m
6,2 kg 7,6 kg
11,5kg
13kg
13,3kg 15kg
11