Installation: A80 Amplifier; Positioning The Unit; Connecting To Loudspeakers; Connecting To A Power Supply - Arcam A80 Manuel

Installation: A80 amplifier

VOLTAGE
SELECT
POWER INLET
115/230V
1 2

Positioning the unit

Place your amplifier on a level, firm surface. Avoid placing the
unit in direct sunlight or near sources of heat or damp.
Ensure adequate ventilation. Do not place the unit in an
enclosed space such as a bookcase or cabinet as both of
these will impede air flow through the ventilation slots.

Connecting to loudspeakers

You can connect one or two pairs of loudspeakers to your
amplifier, provided each pair is rated between 8–16Ω. If one or
both pairs have an impedance of less than 8Ω, the combined
load on the amplifier falls below 4Ω and could cause an
overload. If so, the overload protection circuit may engage and
the amplifier will not work.
To connect one pair of loudspeakers, use the
SP1 and SP2 terminals
Both sets of loudspeaker terminals can be muted by pressing
the
independently, use the front panel switches (see page 6,
the remote control (see page 9).
Your amplifier is fitted with industry standard loudspeaker
terminals. The terminal accepts spade terminals or bare wires.
To connect a spade terminal or bare wire, unscrew the red (or
black) part of the loudspeaker terminal first. Insert the wire or
spade terminal and screw it back up.
Connect the right speaker to the terminals on the back of
your amplifier marked
marked
Connect your loudspeakers so that the red (positive/+) terminal
on each loudspeaker is connected to the red (positive/+)
terminal on the amplifier. Your loudspeaker cables may be
marked to show polarity (negative/– and positive/+), if not,
then the positive terminal can usually be identified by a ridge or
coloured marking.
Now connect your loudspeakers' black (negative/–) terminals to
the black (negative/–) terminals on the amplifier.
Ensure that no stray strands of inner wires are allowed to touch
A80/P80
another cable or the amplifier's casing. This can cause a short
4
circuit and damage your amplifier!
SP2
4 – 16 OHMS
TRIG
OUT
SP1
REMOTE
N
+ –
R
3 4
4
button on the remote control. To switch SP1 and SP2
MUTE
Caution: Do not over tighten the loudspeaker terminals or
use a wrench, pliers, etc., as this could cause damage to
the terminals which will not be covered under warranty.
and the left speaker to the terminals
R
.
L
L
R
+ –
L
PRE OUT LINE OUT
5

Connecting to a power supply

terminals.
SP1
Mains lead
The appliance is normally supplied with a moulded mains plug
already fitted to the lead. If for any reason the plug needs to
be removed, it must be disposed of immediately and securely,
as it is a potential shock hazard when inserted into the mains
2
) or
socket. Should you require a new mains lead, contact your
Arcam dealer.
Wrong plug?
Check that the plug supplied with the unit fits your supply and
that your mains supply voltage agrees with the voltage setting
(
115V
plugging in.
If your mains supply voltage or mains plug is different, consult
your Arcam dealer or Arcam Customer Support on +44 (0)1223
203200.
The product must be earthed.
Plugging in
Push the plug (IEC line socket) of the power cable supplied with
the unit into the socket (
unit. Make sure it is pushed in firmly.
Put the plug on the other end of the cable into your power
supply socket and switch the socket on.
Standby power
For remote standby operation, the amplifier's control power
supply is kept powered up all the time the unit is connected to
the mains supply. The front panel power switch powers down
all other circuitry. Power consumption in this mode is less than
2.5W.
TAPE
RECORD
PLAY
DVD AV TUNER
OUT
IN
6 7 8 9 bk bl bm bn bo
Arcam A80 amplifier
+ –
R
–
+
Right
speaker
Wiring your loudspeakers
or ) indicated on the rear panel of the unit
230V
POWER INLET
CD AUX PHONO
(MM)
+ –
L
+ –
Left
speaker
2 before
1
) in the back of the