Audio Inputs; Recording Loops; Phono Input; Pre-/Power-Amplifier Connections - Arcam RMJ A38 Manuel

audio inputs

Although the inputs are labelled for specific devices, all
have the same characteristics and each may be used with
any line-level product. The exception is the optional
Phono input (see page 16 for specification).
dVd
Intended for the analogue outputs from a DVD-player.
AV
Intended for the analogue outputs from general audio-
visual equipment, such as a VCR, digital TV/satellite
receiver, or Nicam tuner.
tunEr
Intended for the analogue outputs from a radio tuner.
cd
Intended for the analogue outputs from a CD player.
AuX
This is intended for general use. Connect the analogue
audio outputs of any unit with a line-level output (such
as a games console or set-top box).

Recording loops

The A38 is equipped with two recording loops, for use
with recording devices (such as cassette decks, CD
recorders, DAT recorders, VCR, PVR etc.).
AV rEcord out
Connect these output sockets to the input sockets of
your recording device (usually labelled or
rEcord In
AV PLAy In
Connect the output sockets of your recording device
(usually labelled or ) to these inputs.
PLAy out
If you do not have a recording device, you can use this
input for other (line-level) equipment, such as a TV,
DVD, CD-player, radio tuner, PVR, etc.
PVr rEcord out
These output sockets can be connected to the input
sockets of a second recording device.
PVr PLAy In
Connect the output sockets of your second recording
device to these inputs. Alternatively, this input may be
used for other (line-level) equipment such as a games
console, set-top box, etc.
aV dubbing
You can perform tape dubbing from to , but not
PVr AV
from to .
AV PVr
For example, to copy from a cassette recorder connected
to the socket, to a cassette recorder connected to the
PVr
socket, first use the button to select 'Record
AV rEcord
PVR' . This routes the PVR signal to the output.
AV

Phono input

As standard, no phono input is fitted to the A38.
The phono module (or an external phono amplifier) is
required if you wish to connect a record player to the
A38. This is because the low-voltage output of a record
player requires a pre-amplification stage before the signal
can be used.
).
A very high quality phono input is available as an optional
extra: please consult your dealer for price and availability.
The Arcam phono module is compatible with moving-
magnet cartridges (MM) and moving-coil cartridges
(MC). Once the module is fitted, you should select MM
or MC via the recessed back panel switch (push
MM/Mc
the switch in for MC).
If you have already an external phono amplifier that you
wish to use, connect this to one of the line-level inputs,
such as the input.
AuX

controlling a38 from a second room

The A38 will require a remote pick-up device with a 12V external power supply
(such as a Xantech Dinky Link) located in Zone 2, together with a power amplifier
(such as an Arcam A38 or P38) to complete the system.
The diagram below shows the wiring scheme, which will also apply to other IR
pick-up devices commonly available.
The A38 can also provide a +12V trigger output to control devices such as the
power amplifier in Zone 2. The +12V trigger is active when the unit is 'On' .
e-7

Pre-/power-amplifier connections

PrE out
To use your A38 as a dedicated pre-amplifier, or as part
of a bi-amp' e d system, connect the
PrE out
the input sockets of your power amplifier.
Pwr In
To use your A38 as a power-amplifier, connect the
output of your pre-amplifier to the
Pwr In
If you wish to use your A38 as a dedicated pre- or
power-amplifier (but not in the case of a bi-amp' e d
system), press the switch in on the rear panel.
PrE/Pwr
This separates internally the connection between the
pre- and power-amp. stages of the A38.
When used as a power amplifier, your A38 has exactly
the same specification and performance as a P38,
described later in this handbook.
rEMotE In
Tip = Signal
Sleeve = 0V
Dinky Link, located in Zone 2
Signal
����
��
����
��
sockets to
sockets.