SentrySafe SFW123BTC Manuel Du Propriétaire page 2

Water/Fire-Resistant Digital Safe with Fingerprint Scanner
Thank you for choosing SentrySafe to store all your important documents and valuables.
We hope that this product will help you stay organized and provide you with the peace-of-mind of knowing the things most important to you are protected.
Your SentrySafe Product
Your SentrySafe product has a number of features to keep your
important documents and valuables protected including:
Water Protection UL Classified
Fire Protection
Using Your SentrySafe
Preparing Your Safe for First Time Use
1
Slide out the battery drawer on the side
of the keypad. Insert 4 AAA alkaline
batteries (not included). DO NOT use
rechargeable batteries or any other
type of non-alkaline battery.
Do not mix old and new batteries.
Do not mix alkaline and standard batteries.
2 Slide battery drawer back into keypad until it clicks into place.
Using Your Safe
Enter the 5 digit factory code found on the back of this
3
owner's manual.
4
Turn handle downward to open safe.
IMPORTANT: Test your code several times before putting
valuables inside.
IMPORTANT: If you exert too much force on the handle,
the handle will move without moving the bolts. When this
happens, you will hear a 'click.' DO NOT be alarmed.
This feature is designed to protect the bolts from being
overpowered by force. Simply exert force in the opposite
direction (lifting up) until the handle clicks back
into place.
Dual Key Lock
IMPORTANT: A dual key lock option is included
in your safe. Using this key can disable/enable
entry into the safe. This is NOT an override key.
Key must be in horizontal position to access safe.
Your Digital
Fingerprint Lock
The digital lock on your safe comes with two flexible solutions
for entry: a digital keypad and fingerprint scanner. You will
be able to program two 5 digit codes in addition to the factory
code found on the back of this owner's manual. The fingerprint
scanner can also be programmed for up to two users, with two
Digital Media
fingerprints per user.
Protection
NOTE: To add or delete a secondary user's fingerprint, you must
have previously programmed a 5 digit primary user code.
NOTE: Factory code cannot be deleted.
Programming Digital
Keypad Entry
NOTE: Green light will blink to indicate the safe is in
program mode.
To Add a Primary User Code
Only 1 primary user code can be programmed at a time.
1
Press: "P"
2 Enter the 5 digit "FACTORY CODE"
(found on the back of this owner's manual).
3
Press a 5 digit primary user code you have
chosen for your safe
Deleting a Primary User Code
1
Press: "P"
2 Enter the 5 digit "FACTORY CODE"
(found on the back of this owner's manual).
3
Press: "0" –"0" –"0" –"0" –"0"
NOTE: The electronic lock will NOT indicate that it has
deleted the user code—please test code to make sure it
has been deleted.
NOTE: A primary user code is necessary to adding/deleting
a secondary user code/fingerprint.
Programming the Secondary Code
Only 1 secondary user code can be programmed at a time.
1
Press: "P"
2
Enter your programmed 5 digit primary user code.
3
Press a personal 5 digit secondary user code.
Deleting a Secondary Code
1
Press: "P"
2
Enter your programmed 5 digit primary user code.
3
Press: "0" –"0" –"0" –"0" –"0"
NOTE: The electronic lock will NOT indicate that it has
deleted the user code—please test code to make sure it
has been deleted.
Tips for Using Your
Fingerprint Scanner
• Do not choose a finger with a cut or scar.
• Make sure hands are clean and dry before programming or
operating the fingerprint scanner.
• For optimal performance, clean the fingerprint sensor periodically
with a dry, lint-free cloth.
• The fingerprint sensor may not work well when cold.
Programming Your
Fingerprint Scanner
NOTE: Green light will blink to indicate
the safe is in program mode.
NOTE: Each user will have the ability
to program two fingerprints.
NOTE: Turning the keypad sound off
may make it more difficult to use
fingerprint scanner as a single beep
indicates your finger has been scanned.
To Add a Primary Fingerprint User
1
Press: "P"
2
Enter the 5 digit "FACTORY CODE"
(found on the back of this owner's manual).
NOTE: Blue light will blink to indicate the fingerprint
sensor is ready to scan a new fingerprint.
3
Swipe the first finger 5-10 times.
Between each finger swipe you should hear a single beep
to indicate the fingerprint was scanned.
4 When the safe has registered the first fingerprint the green
indicator light will blink 3 times and you will hear
3 beeps.
5
To register a second fingerprint for this user – immediately
repeat steps 3 & 4 with a second finger for this user.
-OR-
If you would like to program only one finger
press "C".
Deleting a Primary Fingerprint User
1
Press: "P"
2 Enter the 5 digit "FACTORY CODE"
(found on the back of this owner's manual).
3
Swipe any fingerprint once.
4
Press: "C"
NOTE: The electronic lock will NOT indicate that it has
deleted the user's fingerprint—please test to make sure
it has been deleted.
NOTE: This will delete both fingerprints for this user.
English