Publicité
Les langues disponibles
Les langues disponibles
Information
These instructions concern only the electrical installation and the use of the control system with the equipment SC24.
The presetting of the electrical connections of all devices of your system must be carried out before starting component installation,
following the "Electric system presetting" diagram provided in the actuator instruction manual, the warnings provided in this manual and
the instructions enclosed with the installed components.
During assembly, installation and test operations of the automatic device, hazardous situations might arise if the safety warnings contained
in the instructions are not followed. Carefully read this instruction manual before proceeding. Instructions must be available with the
system for any use or maintenance operation needed.
Instructions for Aprimatic products can be found at www.aprimatic.it
The data indicated are to be considered for indicative purposes only. The manufacturer is not to be held responsible for any inaccuracy
contained in this manual arising from printing or transcription mistakes.
The company reserves the right to make changes to improve the product without giving prior notice.
Warning
where children can reach them as they are a potential source of danger. Wrong installation of the equipment can cause serious danger.
Please, follow all installation instructions carefully. We recommend operating in a well-lit and healthy environment, in compliance with the
safety regulations in force. We recommend the use of approved protective clothing (safety shoes, protective goggles, gloves and helmet).
Do not wear articles of clothing that could get caught. Take adequate safety measures to prevent the risk of injury caused by sharp splinters
and the possible risks of crushing, knocks and cuts and amputation collision and shearing danger. We recommend strict observation of the
national regulations for safety in work sites. Delimit the yard to prevent any unauthorised persons from transiting in the working area. Do
not leave the working area unattended. Installation, electrical connections and adjustments must be carried out in a professional manner in
compliance with the good manufacturing and workmanship regulations in force in the country where the automation is installed. The
manufacturer of the device is not responsible for the non-observance of professional standards of work in the construction of the power-
driven structure, nor for any damage which may be caused by the use of the drive.
Incorrect installation may be dangerous. Follow the manufacturer's instructions.
Before starting installation, check that the product is intact and that the existing structure is suitably strong and stable and that it is
complying with the sector current regulations. Only suitably skilled technicians trained on the product are authorised to connect up, test
and put into service this product.
The whole system must be built by qualified personnel and in full compliance with the regulations in force in the country of installation
(standards CEI 64 - 8 / EN 60335-1).
We strongly recommend attending a specialised training course. Installers should contact the supplier for information on courses.
Warning
The equipment SC24 is designed to control functioning of 24-volt electromechanical actuators used to
automate sliding gates.
Do not use the product improperly or for purposes other than those specified. You should note the operating restrictions specified
in the installation manual supplied with the actuator. Do NOT tamper with or modify the product in any way. The product must
only be installed using APRIMATIC material.
Aprimatic srl declines all liability for damages caused by failure to follow these instructions.
The equipment can be used by children who are over 8 years of age and by persons with limited physical, sensory or mental
capacities, or inexperienced or unskilled persons, provided that they are under supervision or that they have been instructed about
the safe use of the equipment and inherent hazards.
Children must be supervised so that they do not play both with the equipment and the remote control. Cleaning and maintenance
operations intended to be carried out by the user must not be performed by unsupervised children.
Caution
requirements, in compliance with local system safety regulations.
Before connecting the power supply make sure that the plate data correspond to those of the electric power distribution grid. The
protection measures on the primary are used on site / in operation.
The equipment must be secured to a switch (including a thermal-magnetic circuit breaker if necessary) that ensures the omnipolar
disconnection of the mains. As main switch of the mains power, use a 6A magneto-thermal differential switch tripping at 30mA, category
III.
Disconnect the power supply before carrying out any other maintenance operation, repair or replacement, both mechanical and electrical.
Test and commissioning of the automatic device are not allowed until the sliding automatic gate has not been verified as complying with
the requirements that the finished, assembled and installed gate is subject to.
The installer must check that the temperature range indicated on the label is compatible with the place of installation.
The installer must keep and store the technical documentation of the automatic gate and must fulfil all obligations required. At the end of
the job the installer must check the installation and the correct operation of the automatic device.
LBT0499 – DS41627-001 – FW 1.01 2020
GENERAL SAFETY PRECAUTIONS
Carefully read the instructions before starting to install the product.
Packaging materials (plastic, polystyrene, etc.) must not be dispersed in the environment and must not be left
The power supply system must be built by a qualified and expert electrician according to the local
ABOUT THIS MANUAL
Publicité
