Table des Matières
Publicité
Continued from front
Access the "File" menu and select "New Project".
The new project window appears. Here you can select a project
template.
Make sure that the "Empty" template is selected, and
click the OK button.
A window for selecting the project file save location appears.
After specifying the project file save location (such as
the desktop), click the OK button (Choose button in
MacOS 10.4).
A new project is created, and the project window for controlling most
of the Cubase LE operations appears.
Project window
To create a new audio track, access the "Project"
menu and select "Add track". In the submenu that
appears, select "Audio".
A new audio track is added to the project window.
HINT
You can add several tracks at once by accessing the "Project" menu,
selecting "Add track" and then selecting "Multiple..." in the submenu.
Cubase LE Installation
Connections and Preparations
Make the following settings for the new audio track.
1.
Drag the audio track boundary to the right
to display all buttons.
2.
Verify that the Monitoring On button is
Off (grayed out). If the button is On,
click the button to turn it Off.
3.
Click the Stereo/Mono button to set the audio track to
Stereo. When the button is not grayed out and has changed
from [
] to [
], the track is active as a stereo track.
Access the "Devices" menu and select "VST Inputs".
The VST inputs window appears.
This window shows the available input ports and their active/inactive
status.
You can perform the following steps here.
2.
Verify that the Active button for USB Audio CODEC
1/2 (USB Audio CODEC L/R on MacOS X) is enabled
(not grayed out). If the button is grayed out, click the
button to enable it.
VST input window
1.
When there are multiple input ports,
drag here to enlarge the window.
Connect the guitar to the [INPUT] jack of the G2.1u
and select the desired patch.
The sound selected here will be recorded on the computer via the
[USB] port.
Access the "Devices" menu and select "Mixer".
The mixer window appears.
This window shows the channels assigned to created tracks.
You can perform the following steps here.
Recording with Cubase LE
Windows XP
2.
Click here to select the port for the USB Audio CODEC
1/2 (USB Audio CODEC L/R on MacOS X) assigned as
audio input port to the channel (see step 13).
Mixer window
1.
To adjust the playback level after
recording, click this button to bring
up the master channel of the mixer.
4.
Click here to set the
audio output port of
the master channel
to "USB Audio
CODEC".
Channel assigned to audio track
Master channel
3.
Verify that the Record Standby button is shown in red. (If
the button is grayed out, click the button to enable it. This
will set the audio track to the recording standby condition.)
HINT
When the Record Standby button is enabled, the level meter next to
the fader shows the input level for the audio track. When the button is
disabled, the output level for the audio track is shown.
While playing your guitar, adjust the output level of
the G2.1u to achieve a suitable recording level for
Cubase LE.
Level meter
When the audio track is in recording standby mode,
its recording level is shown by the level meter for the
assigned channel. The level should be set in such a
way that the meter registers to a fairly high value but
remains below the maximum point.
NOTE
• The level meter shows the signal level after
internal processing by Cubase LE. Therefore
a slight time lag may occur between playing a
guitar string and the meter registering the
change in level. This is normal and not a
defect.
• The audio tracks of Cubase LE will be
recorded with correct timing exactly matched
to your guitar play. There will be no lag
between already recorded tracks and newly
added tracks.
Verify that the transport panel is shown.
Transport panel
If the transport panel is not shown, access the "Transport" menu and
select "Transport Panel".
MacOS X
To start recording, click the Record button in the
transport panel.
As you play your guitar, the waveform appears in real time in the
project window.
To stop recording, click the Stop button in the
transport panel.
Recording stops.
Check the recorded content.
To play the recording, perform the following steps.
1.
Move the fader
of the master
channel (as
4.
Raise the fader of
displayed in step
the master channel
15) fully down.
to obtain a suitable
volume.
Go to beginning of project
3.
2.
Click the Play button in
Use the controls on the
the transport panel to
transport panel to move to
start playback.
the beginning of the project.
HINT
If no sound is heard when you click the Play button after recording,
check the settings in the VST input window (step 13) and the master
channel output port setting (step 15) once more.
For optimum enjoyment
While using Cubase LE, other applications may slow down drastically
or the message "Cannot synchronize with USB audio interface" may
appear. If this happens frequently, consider taking the following steps
to optimize the operation conditions for Cubase LE.
(1) Shut down other applications besides Cubase LE. In
particular, check for resident software and utilities.
(2) Reduce plug-ins (effects, instruments) used by Cubase LE.
When there is a high number of plug-ins, the computer's
processing power may not be able to keep up. Reducing
the number of tracks for simultaneous playback can also be
helpful.
(3) Power the G2.1u from an AC adapter.
When powered via the USB port, the current supply may sometimes
fluctuate, leading to problems. See if using an AC adapter improves
operation.
If applications still run very slowly or the computer itself does not
function properly, disconnect the G2.1u from the computer and shut
down Cubase LE. Then reconnect the USB cable and start Cubase LE
again.
Record button
Play button
Publicité
Table des Matières
