Basic Settings; Setting Speakers Quickly - JVC RX-DV31SL Manuel D'instructions

Basic Settings

Some of the following settings are required after connecting
and positioning your speakers while others will make
operations easier.
7 Quick speaker setup (see below)
7 Basic item setup (see pages 22 to 25)
• Speaker settings
– Speaker information for subwoofer, front, center, and
surround speakers*
– Speaker distance for front, center, and surround
speakers*
– Crossover frequency*
– Low frequency effect attenuator*
– Dynamic range compression*
• Digital input (DIGITAL IN) terminals
• Auto surround
• Video output mode
* You can also set these items using the Choice menu (see pages 51
to 56).

Setting Speakers Quickly

You can register the speaker size and distance easily for the
connected speakers (Quick Setup).
• To set the speaker size and distance manually, see
"Speaker information" and "Speaker distance" on page 23.
On the front panel ONLY
Before you start, remember...
There is a time limit in doing the following steps.
If the setting is canceled before you finish, start from step 1
again.
1
Press SETTING.
The CONTROL buttons now work for basic settings. The
setting item selected previously appears on the display.
For the configuration of the basic setting items, see
"Configuration of the items on the display" on page 22.
2 Press CONTROL ∞ (or 5) repeatedly until
"QUICK SETUP" appears on the display.
ANALOG DIGITAL AUTO PL DSP SLEEP PROGRAM REPEAT
PPCM AUTO SURROUND
GROUP TITLE TRACK CHAP. RESUME
L C R
DIGITAL
SUBWFR LFE
LPCM
MPEG-2 AAC LS S RS
3
Press MEMORY.
"ENTER THE NUMBER OF SPEAKERS" scrolls on the
display, then "5 SPEAKERS" appears.
21
1A-B RANDOM PROGRESSIVE RDS TA NEWS INFO INPUT ATT
SPK 1 2 REC
AUTO MODE
B.S.P BONUS TUNED STEREO AUTO MUTING
A.POSITION
kHz
MHz
VOL
4
Press CONTROL 3 (or 2) to select an
appropriate number of the connected
speakers.
• Each time you press the button, the indication changes
as follows:
ANALOG DIGITAL AUTO PL DSP SLEEP PROGRAM REPEAT
PPCM AUTO SURROUND
GROUP TITLE TRACK CHAP. RESUME
DIGITAL L C R
LPCM SUBWFR LFE
MPEG-2 AAC LS S RS
5 SPEAKERS
4 SPEAKERS
5 SPEAKERS Select when the front, center, and
surround speakers are connected (initial
setting).
4 SPEAKERS Select when the front and surround
speakers are connected.
3 SPEAKERS Select when the front and center
speakers are connected.
5
Press MEMORY.
"ENTER USE OF SUBWOOFER" scrolls on the display,
then "SUBWFR USE" appears.
6 Press CONTROL 3 (or 2) to select whether
you have connected a subwoofer or not.
• Each time you press the button, the indication changes
as follows:
ANALOG DIGITAL AUTO PL DSP SLEEP PROGRAM REPEAT
PPCM AUTO SURROUND
GROUP TITLE TRACK CHAP. RESUME
L C R
DIGITAL
SUBWFR LFE
LPCM
MPEG-2 AAC LS S RS
USE Select when a subwoofer is connected (initial
setting).
NO Select when no subwoofer is used.
7
Press MEMORY.
"ENTER ROOM SIZE" scrolls on the display, then "SMALL
ROOM" appears.
8
Press CONTROL 3 (or 2) to select an
appropriate room size to match your
listening room.
• Each time you press the button, the indication changes
as follows:
ANALOG DIGITAL AUTO PL DSP SLEEP PROGRAM REPEAT
PPCM AUTO SURROUND
GROUP TITLE TRACK CHAP. RESUME
DIGITAL L C R
LPCM SUBWFR LFE
MPEG-2 AAC LS S RS
SMALL
LARGE
Select an appropriate room size according to the distance
from your listening point to the speakers. See "Speaker
distance for each room size" on page 22.
1A-B RANDOM PROGRESSIVE RDS TA NEWS INFO INPUT ATT
REC
SPK 1 2
AUTO MODE
B.S.P BONUS TUNED STEREO AUTO MUTING
A.POSITION
kHz
MHz
VOL
3 SPEAKERS
1A-B RANDOM PROGRESSIVE RDS TA NEWS INFO INPUT ATT
SPK 1 2 REC
AUTO MODE
B.S.P BONUS TUNED STEREO AUTO MUTING
A.POSITION
kHz
MHz
VOL
USE NO
1A-B RANDOM PROGRESSIVE RDS TA NEWS INFO INPUT ATT
SPK 1 2 REC
AUTO MODE
B.S.P BONUS TUNED STEREO AUTO MUTING
A.POSITION
kHz
MHz
VOL
MEDIUM