Terex Genie ZX-135/70 Manuel De L'opérateur page 9

Deuxième édition • Deuxième impression
160576
133236
DANGER
3
Platform uphill:
Stop all movement.
1L ower primary boom.
2 Retract/lower secondary boom.
3 Retract primary boom.
3
Tip-over Hazard
If tilt-alarm
sounds, uniti so n
• Read operator's Platform downhill:
as evere slope. manual before 1 Retract primary boom.
Death or serious attempting to move 2 Retract/lower secondary boom.
injury will result. machine.
3L ower primary boom.
133236 A
97579 82862
DANGER
+
=
+
Tip-o ver Hazar d Do not o verload
Welder power supply platf orm.
reduces rated platform
Welder power supply
capacity and
weighs 75 lbs / 34 kg.
must be factored into total
platform load.
97579 D
114390
DANGER
72875
WARNING
Bodily Injury Hazard
Failure to usep ipe cradle assembly accordingt oi nstructions and safetyr ules
belowa nd in operator's and responsibilities manualc ould result in deatho r
seriousi njury.
Do note xceedr ated platform capacity. Securel oad to platform.
Pipec radlea ssembly and weighti np ipe
Do not obstruct entrance/exit of platform.
cradles will reduce ratedp latform capacity
Do not obstruct abilityt o operate platform
and must be factored into total platform
controlso rr ed Emergency Stop button.
load.
Do not operate unless youa re adequately
Pipe cradle assemblyw eighs 21 lbs/
instructed and area ware of allh azards
9.5 kg.
associated with movement of platform
Maximum capacity of pipe cradle assembly
witho verhanging load.
is 200 lbs/9 1k g.
Do not cause a horizontalf orce or side
Weight of pipe cradle assembly and load in
load to machine by raisingo rl oweringa
pipe cradles may limit maximumn umber of
xedo ro verhanging load.
occupantsi np latform.
ElectrocutionH azard: Keep pipes away
Center load within perimeter of platform.
froma ll energizede lectrical conductors.
Pièce réf. 1272822FRGT
160580
WARNING
Runaway Hazard
Machine movement can occur
when a machine is operated
on a slope that exceeds rated
uphill, downhill or side slope
rating.
A runaway machine could result
in death or serious injury.
160580 A
DANGER
82237
82410
WARNING
Bodily Injury Failuret ou se panelc radles accordingt o instructionsa nd safety rules
Hazard below and in operator's and responsibilities manual couldr esulti n death
or serious injury.
Do not exceed ratedp latform Weight of panel cradles and load Do notc auseah orizontalf orce
capacity.Combined weight in panel cradles may limit or sidel oad to machine by
of cradles, panels, maximum number of occupants raisingo rl oweringa xed or
occupants, tools and any in platform to one person. overhangingload.
other equipment must not
Secure cradles to platform. Maximumv ertical height of
exceed rated capacity.
Secure panel(s) to platform panels: 4f t/ 1.2m
Panel cradlea ssembly railingu sing straps provided.
Maximum wind speed:
weighs 30 lbs/ 13.6k g.
Do not operate unlessy ou are 15 mph/6 .7 m/sec
Maximum capacity of panel adequatelyi nstructed and are
Maximump anel area:
cradlesi s2 50 lbs/1 13 kg. awareo fa ll hazardsa ssociated
32 sq. ft/3 m 2
with lifting panels.
28236
WARNING
Driving On a Slope
Do not drive machine on a slope that exceeds
maximum uphill, downhill or side slope rating.
Determine slope and side slope ratings for
machine and determine slope grade.
Maxi mum slope rating,
counterweight up hill
(gradeability): 45% (24°)
Maxi mum slope rating,
counterweight downhill 30% (17°)
Improper operation or
Maxi mum
maintenance can result in
side slope rating 25% (14°)
serious injury or death.
Note: Sloper ating is subject to ground conditions
and adequate traction. Gradeability applies to
platform downhill con guration only.
Be sure boom is below horizontal and
platform is between non-steer wheels.
Move drive speed select switcht om achine
on incline symbol.
219487
ZX-135/70
Manuel de l'opérateur
Sécurité générale
97875
Read and understand Operator's
Manual, Responsibilities Manual and
Safety Manual and all safety signs
before using or maintaining machine.
If you do not understand the
information in the manuals, consult
your supervisor, the owner or the
manufacturer.
28236 D
218559
CAUTION WARNING
Drive Direction Hazard
Machine can move in opposite direction of
joystick movement. Movement in an unplanned
Tip-over Hazard
direction can result in death or serious injury.
Tipping over this machine will
result in death or serious injury.
Always match the color-coded direction arrows
on platform controls and drive chassis to
Only raise the platform when the
determine direction of machine travel. Read
machine is on a frm, level surface .
and understand operator's manual.
218559
219487
160576
133236
114390
160580
97579
28236
82862
97875
72875
82410
82237
WARNING
Crush Hazard
Contact with overhead obstructions
could result in death or serious injury.
Keep away from overhead obstructions
or other possible hazards.
218559 A
7