Remote Control - Revell Control SKY SPIDER Mode D'emploi

1 QUaDroCopTer
1A Canopy
1B Front propeller (orange)
1C Rear propeller (black)

2 reMoTe CoNTrol

2A Antenna
2B Power LED
2C Trim adjustment for forward and
backwards flight
2D 3-stage switch for 30%, 60% and
100% control effect and looping
function
3 INSerTINg BaTTerIeS (reMoTe CoNTrol)
3A Unscrew the screw 3B Insert 6 x 1.5 V AA batteries
and remove the
and pay attention to the
cover
polarity, as shown in the
battery compartment.
4 ChargINg The QUaDroCopTerS
Attention: The battery and motor must cool down for 10 to 15 minutes before
charging and after every flight. Otherwise they can be damaged. The charging process
must be constantly monitored. Always ensure that the charging process takes place on
a fireproof surface in a fire-resistant environment.
• Unplug the quadrocopter from the battery, switch off the remote control and plug the
charger into an outlet. The control LED on the charger illuminates green (4A).
• Remove the battery from the battery compartment (do not hold by the cable!) (4B).
• Now plug the battery into the cable of the charger. Pay attention to the polarity.
Please do not use force. The LED on the charger illuminates red when the charging
process begins.
• The charging process lasts approx. 70 minutes and must be continuously monitored.
The LED illuminates green when the charging process is finished.
• Disconnect the battery from the charger and disconnect the charger from the mains
after the charging is completed (4C).
16
1D Battery compartment
1E Battery connection cable
1F Battery plug
2E Control for forward and backwards
flight as well as banking
2F Trim adjustment for banking
2G ON/OFF switch
2H Control for thrust and rotation
2I Trim control for rotation
3C Put the cover on
again and screw
it in place.
After a charge time of approx. 90 minutes the quadrocopter can fly for
approx. 5-7 minutes.
Warning notice: The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
5 STarT preparaTIoN
The thrust controller (the left controller on the remote control) must point down before
being switched on (5A). Then move the ON/OFF switch (5B) on the remote control to
"ON" and the Power LED blinks (5C). Connect the battery cable to the connection cable
(5D). Now the LED on the quadrocopter starts blinking red. Place the quadrocopter on
the ground so that the tail faces towards you, both black propellers are in the rear and
the orange propellers are in the front. For the initialisation the control fro thrust must
briefly be pushed up and then back down again. The Power LED on the remote control
is now permanently illuminated.
Attention! Make sure that you place your quadrocopter on a level surface – the control
electronics align their neutral position to the ground!
6 TrIM aDJUSTMeNT oF The CoNTrol
The correct trim is a basic requirement for fault-free flying behaviour of the quadrocopter.
Its adjustment is simple, but it requires some patience and a feel for it. Please observe
the following instructions precisely: Carefully move the thrust control up and raise the
quadrocopter approximately 0.5 to 1 metre in altitude.
6A If the quadrocopter moves by itself slowly or quickly to the left or right ...
press the trim adjustment for banking incrementally in the opposite direction.
6B If the quadrocopter moves by itself slowly or quickly around its own axis ...
press the trim adjustment for rotation incrementally in the opposite direction.
6C If the quadrocopter moves by itself slowly or quickly forwards or
backwards ...
press the trim adjustment for forward and backwards flight incrementally in the
opposite direction.
17