Remote Control - Revell Control FORMULA Q FPV Manuel De L'utilisateur

• Never disassemble or alter the battery
contacts. Do not damage or puncture
the battery cells. There is a risk of
explosion!
• The LiPo battery must be kept out of
reach of children.
• When disposing of batteries, they
must be discharged or their capacity
must be fully depleted. Cover exposed
terminals with adhesive tape in order
to prevent short-circuiting!
Maintenance and care:
• Please only use a clean, damp cloth
to wipe off the model.
• Protect the model and batteries from
direct sunlight and/or direct heat.
• Never allow the remote control and
charging unit to come into contact
with water, because the electronics
will be damaged as a result.
Technical changes and differences in
color reserved!
1A Status LED
1B Rotors
1C Protective guard
1D Battery compartment cover
1E Battery compartment securing screw

2 rEmotE control

2A Control for thrust and rotation,
Speed levels
2B Control for forward/backward
and sideways, Flip function
2C Trim for rotation
2D Trim for forwards/backwards
2E Trim for sideways
2F ON/OFF switch
2G Button for shooting photos
3 insErting battEriEs (rEmotE control)
3A Cover (2O) removal. 3B Insert 4 x 1.5 V AA batteries
and pay attention to the
polarity specifications, as
indicated in the battery
16
compartment.
Required batteries for the model:
Power supply:
Rated output:
1 x DC 7,4 V / 8,9 Wh
rechargeable
LiPo battery (included)
Capacity: 1200 mAh
Battery requirement for the
remote control:
Power supply:
DC 6 V
Batteries:
4 x 1.5 V "AA"
(not included)
Charger:
Power supply:
110-240 V AC; 50-60 Hz;
Rated output:
7,4 V DC; 800 mA
1 modEl
1F ON/OFF switch
1G Camera connection
1H Moving lens
1I micro SD card slot
2H Button for video recording
2I Setup button
2J Coming Home button
2K Headless mode button
2L Selection button
2M Status LED
2O Battery compartment cover
2P micro SD card slot
3C Close the battery
compartment cover.
4 charging thE modEl
Attention: The battery and motor must cool down for 15 to 30 minutes before charging
and after every flight. Otherwise they can be damaged. The charging process must
be constantly monitored. Always ensure that the charging process takes place on a
fireproof surface in a fire-resistant environment.
• Open the battery compartment cover (1D) by unscrewing the battery compartment
securing screw (1E) in anti-clockwise motion and disconnect (4A) the plug from
the camera connection (1G). Unplug the battery from the model (4B) and switch off
the remote control (4C). Remove the battery from the model. Plug the charger into an
unoccupied socket (4D). The status LED on the charger begins to
illuminate.
• Plug the white balancer plug into the charging socket of the charger and ensure the
correct polarity (4E). The battery must be gently inserted into the charging socket –
DO NOT USE FORCE. If the battery is not correctly inserted into the charging socket,
the battery may become damaged and, under certain circumstances, cause injury.
• The status LED on the charger will light up red when charging begins.
• The charging process lasts approx. 140 minutes and must be continuously monitored.
The colour of the LED on the charger changes from red to green when the charging
process is finished.
• Disconnect the battery from the charger and disconnect the charger from the outlet
after the charging is completed.
The model can fly for approx. 6-8 minutes after a charge time of approx.
140 minutes.
Warning notice: The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
5 start prEparation
The model must be switched on first in order to connect it to the remote control. Open
the battery cover (1D), insert the battery into the battery compartment of the model, plug
the battery plug into the socket in the model, and close the battery compartment. Do not
use force and ensure the correct polarity (5A). Then set the ON/OFF switch on the
model (1F) to the „ON" position.
Before switching on the remote control, the control for thrust and rotation (2A) must
point down (5B). To switch on the remote control, move the ON/OFF switch (2F) to
the ON position and briefly push the control for thrust and rotation upwards. After
approx. 3 seconds, the model activates and is ready for use.
A pair of landing skids is included with the mode. This is placed in the groove on the
underside of the model (5C). Then carefully screw in two securing screws in each skid.
micro SD card: Please insert the accompanying micro SD card in the rear slot of the
camera (1I) with the contacts facing down (5D). Press down on the memory card
with your finger nail to remove it. Attention: HC memory cards are not supported.
Attention: A memory card can also be inserted in the micro SD card slot (2P) on
the remote control. It is mainly used to check the quadrocopter videos. If videos are
recorded directly in the remote control, the quality is significantly lower because of the
video transmission.
Once you have finished flying, switch the model off first and then the remote control.
Unplug the battery from the model and remove the battery from the model.
17