Remote Control - Revell Control SPOT Mode D'emploi

1 QUaDroCopTer
1A Rotors 1D Lens
1B Cap 1E Gears and outdrives
1C Landing skid 1F Protective rings

2 reMoTe CoNTrol

2A Yaw trim
2B Control mode switch
2C Roll trim
2D Photo button
2E Video button
2F Power LED
2G Control for nick and roll
3 INSerTINg BaTTerIeS (reMoTe CoNTrol)
3A To open the battery 3B Insert 2 x 1.5 V AAA
compartment, unscrew
batteries and pay attention
the locking screw
to the polarity, as shown in
counter-clockwise and
the battery compartment.
open the flap.
4 ChargINg The QUaDroCopTer
Attention: The battery and motor must cool down for 10 to 15 minutes before
charging and after every flight. Otherwise they can be damaged. The charging process
must be constantly monitored. Always ensure that the charging process takes place on
a fireproof surface in a fire-resistant environment.
• Unplug the quadrocopter from the battery and switch off the remote control (4A).
• Remove the battery from the battery compartment (do not hold by the cable!) (4B).
• Plug the charger into a free USB port and connect the battery to the charger (4C).
The charger flashes.
• The charging process starts automatically and must be continuously monitored.
The charger flashes slowly during the charging process. (quick flashing indicates a
malfunction – the charging process must be stopped immediately.) As soon as the
charging process is complete, the charger lights up continuously.
• Disconnect the battery from the charger and disconnect the charger from the USB
port once charging is complete.
After a charge time of approx. 70 minutes the quadrocopter can fly for
approx. 5-7 minutes.
Warning notice: The battery does not normally heat up while charging. If it should
become warm and/or changes to the surface begin to appear, immediately discontinue
the charging process!
16
1G Micro-SD card slot
1H Battery compartment
1I Battery plug
2H Nick trim
2I ON/OFF switch
2J Thrust trim
2K Control for thrust and yaw
2L Battery compartment securing screw
2M Battery compartment
3C Replace the cover
and screw in the
securing screw
clockwise.
5 MoDe 1 aND MoDe 2 SWITCh
The remote control can be switched from Mode 1 (thrust/yaw on the right stick,
nick/roll on the left stick) to Mode 2 (thrust/yaw on the left stick, nick/roll on the
right stick).
To do this, push the mode switch (5A) for Mode 2 to the left (standard). Push the
switch for Mode 1 to the right and turn the remote control 180°.
Important: Only switch with the remote control turned off.
6 STarT preparaTIoN
The thrust controller (the left controller on the remote control) must point down
before being switched on (6A). Then set the ON/OFF switch of the remote control
to the „ON" position; the Power LED will flash red (6B) Place the quadrocopter on
the ground so that the tail points toward you - WITHOuT connecting the battery!
(6C). Only connect the battery with the connection cable when the quadcopter is
standing level (e.g. on a table) Do not move the quadcopter when connecting the
battery - otherwise, the quadcopter will not fly! (6D). Now the LEDs on the
quadrocopter start to flash. Do not move the quadrocopter while the LEDs are flashing.
The quadrocopter needs around 5-10 seconds to initialize the gyro and to establish the
connection to the remote control. Once the LEDs on the quadrocopter are continuously
lit, the connection to the remote control has been established. Now move the thrust
controller forwards once all the way and back to zero again, the remote control beeps
once and the quadrocopter is ready for use.
Warning! Always place your quadrocopter on an even horizontal surface – the control
electronics aligns its neutral position to the subsurface!
7 TrIM aDJUSTMeNT oF The CoNTrol
The correct trim is a basic requirement for fault-free flying behaviour of the quadrocopter.
Its adjustment is simple, but it requires some patience and a feel for it. Please observe
the following instructions precisely: Carefully move the thrust control up and raise the
quadrocopter approximately 0.5 to 1 metre in altitude.
7A If the quadrocopter moves by itself slowly or quickly to the left or right ...
press the roll trim gradually in the opposite direction.
7B If the quadrocopter moves by itself slowly or quickly around its own axis ...
press the yaw trim in the opposite direction.
7C If the quadrocopter moves by itself slowly or quickly forwards or backwards ...
press the nick trim gradually in the opposite direction.
7D If the quadrocopter rises too quickly or slowly ...
press the thrust trim gradually in the opposite direction.
17