Technical Data; Motor; Charger; Battery - Sabo 36-ACCU Livret D'entretien

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 19
Cutting height set too low
(grass that is too high
prevents the motor
starting).
Too much grass waste in
the housing or ejector
channel.
The charge status of the
An acoustic signal
battery is below 10%.
sounds
Battery is not functional
or cannot be charged.
Acoustic signal sounds
although the battery is
charged: technical defect
of the mower
Cutting height too low.
Motor switches off
during mowing
Battery is empty
Excessive grass waste in
the housing or ejection
channel.
Cutting bar blunt.
Motor power
decreasing
Low battery capacity
Excessive grass waste in
the housing or ejection
channel.
Extreme vibration
Blade blunt.
Unclean cut, lawn is
yellow
Cutting height too low.
Mowing too fast.
Insufficient overlapping
of cuts when mowing.
Lawn becomes matted.
Turbo signal has not
Ejection blocked
been detected
J + K .
Cutting height too low for
grass that is too high.
Pushing mower too fast.
Grass not dry.
Cutting blade blunt.
The mulched grass
does not look good:
clumps, excessive cut
material, coarse cut
Mulching rule ignored
(cut max. 1/3 of grass
height; the grass height
to be cut must be less
than 10 cm)
Driving speed too high.
Set higher cutting height I .
Tilt the machine during start-
up
Clean grass from cutting
area/ejector channel, keep
gap between fan and housing
clean (remove safety key
before hand K2 !).
In case of faults and defects which have not been listed here, please contact the
nearest authorized dealer.
Have it checked by an
authorised workshop.
Repairs which require specialized knowledge should only be performed by a qualified
expert. Your authorized dealer will naturally also be glad to help if you do not wish to
Charge battery (see separate
perform the maintenance work described here yourself.
instructions for the charger).
Replace battery.

18 TECHNICAL DATA

Have it checked by an

Motor

authorised workshop.
Set higher cutting height I .

Charger

Charge battery (see separate
instructions for the charger).
See separate instructions for the charger.
Clear the cutting

Battery

chamber/ejection channel of
grass, keep the gap between
See separate instructions for the charger.
fan and housing clean (remove
the safety key first K2 ).

Mower

Have it sharpened and
36-ACCU
balanced by an authorised
workshop Q .
Charge battery (see separate
instructions for the charger).
Clear the cutting
chamber/ejection channel of
grass, keep the gap between
fan and housing clean (remove
the safety key first K2 ).
Have it checked by an
authorized dealer
Have it sharpened and
balanced by an authorized
dealer Q .
Adjust to higher cutting height
I .
Adjust mowing speed.
40-ACCU
Tall grass conditions may
dictate that more overlapping
of cuts is required.
A lawn scarifier can remedy
the problem considerably
Empty the grass collector L .
Adjust to higher cutting height
I .
Adjust mowing speed.
Let grass dry.
Have it sharpened and
balanced by an authorised
workshop.
43-ACCU
Set higher cutting height I .
Adjust speed.
10
Grass accumulation
under the mower blade.
Insufficient overlap
between mowing lanes.
Grass is damp.
Motor
Motor speed
Housing
Cutting width
Cutting heights
Handlebar height adjustable
Sack volume
Weight
Length
Width
Height
Wheels front / rear
Mount front
Mount rear
Housing
Cutting width
Cutting heights
Handlebar height adjustable
Sack volume
Weight
Length
Width
Height
Wheels front / rear
Bearings front / rear
Housing
Cutting width
Cutting heights
Handlebar height adjustable
Sack volume
Set higher cutting height I .
If grass is long, the mowing
lanes may need to overlap
further.
Set higher cutting height I .
Allow the lawn to dry.
40 V DC motor
2800 rpm
Aluminium pressure die-casting
360 mm
Central, 20, 28, 35, 45, 55, 70 mm
3 heights
43 litres
20.5 kg
1265 mm
420 mm
980 mm
Ø 150 mm / Ø 175 mm
Cone ball bearings
Cone ball bearings
Impact-proof plastic (PP)
400 mm
Central, 24, 32, 40, 50, 60, 75 mm
3 heights
44 litres
19 kg
1400 mm
455 mm
970 mm
Ø 150 mm / Ø 180 mm
Cone ball bearings
Aluminium pressure die-casting
430 mm
Central, 22, 30, 35, 42, 50, 60, 80 mm
3 heights
55 litres

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

40-accu43-accuSa1780Sa1781Sa1782

Table des Matières