Fault Display (Fig. H (10) ); Technical Data - Sabo 43-ACCU VARIO Livret D'entretien

Cutting bar blunt.
Motor power
decreasing
Low battery capacity
Excessive grass waste in
the housing or ejection
channel.
Pull drive control bar not
Mower does not work
pulled.
Standby mode not on.
Centrifugal clutch of the
Mower cannot be
drive still engaged.
moved backwards
Standby mode not on.
Speed cannot be
regulated
Extreme vibration
Cutting blade blunt.
Cut not clean, lawn
turns yellow
Cutting height too low.
Mowing speed too high.
Insufficient overlap
between mowing lanes.
Lawn matted.
Mowing in energy-saving
mode under difficult
conditions.
Turbo signal ignored J +
Ejector blocked
K .
Cutting height too low
with grass too high.
Mowing speed too high.
Grass is damp.
Mowing in energy-saving
mode under difficult
conditions.
Cutting blade blunt.
The mulched grass
does not look good:
clumps, excessive cut
material, coarse cut
Mulching rule ignored
(cut max. 1/3 of grass
height; the grass height
to be cut must be less
than 10 cm)
Driving speed too high.
Grass accumulation
under the mower blade.
Insufficient overlap
between mowing lanes.
Grass is damp.
In case of faults and defects which have not been listed here, please contact the
Have it sharpened and
nearest authorized dealer.
balanced by an authorised
workshop Q .
Repairs which require specialized knowledge should only be performed by a qualified
expert. Your authorized dealer will naturally also be glad to help if you do not wish to
Charge battery W1 .
perform the maintenance work described here yourself.
Clear the cutting
chamber/ejection channel of

21 FAULT DISPLAY (FIG. H (10) )

grass, keep the gap between
fan and housing clean (remove
Frequency of the
the safety key first K2 ).
flashing signal / signal
Pull drive control bar G .
tone
Before moving the drive
safety control bar, switch on
standby mode (9) H .
Have it checked by an
authorised workshop.
Push mower forwards
minimally without the on to
release the clutch.
Before activating the speed
adjustment, switch on
standby mode (9) H .
Have it checked by an
authorised workshop.
Have it checked by an
authorized dealer
Have it sharpened and
balanced by an authorised
workshop Q .
Set higher cutting height I .
Adjust mowing speed.
If grass is long, the mowing
lanes may need to overlap
further.
A perceptible improvement
can be achieved by using a
scarifier.
Switch off energy-saving
mode.
Empty the collecting bag L .
Set higher cutting higher I .
Adjust mowing speed.
Allow the lawn to dry.
Switch off energy-saving
mode.
Have it sharpened and
balanced by an authorised
workshop.
Set higher cutting height I .

22 TECHNICAL DATA

Convert mower to rear
ejection U2 + S1 and mow
Cutter motor
lawn with high cutting height
first.
Adapt driving speed, switch
motor drive off if necessary.
Set higher cutting height I .
If grass is long, the mowing
lanes may need to overlap
further.
Set higher cutting height I .
Charger
Allow the lawn to dry.
See separate instructions for the charger.
11
Meaning
Motor does not reach the
1 x
set speed.
Fault with control circuit
2 x
board when starting.
Communication between
3 x
battery and control circuit
board interrupted.
Overload on cutter motor
4 x
or drive motor.
Battery capacity low.
5 x
Motor, control circuit
6 x
board or battery
overheated.
Overload on cutter motor
7 x
or drive motor.
Control element for
8 x
starting the cutter motor
activated in the wrong
order.
Software error.
9 x
Motor
Motor speed
Standard setting
Energy-saving mode
Automatic speed increase
under difficult mowing conditions
Correcting the fault
Restart motor.
Check the battery is
charged., charge if
necessary.
Have it checked by an
authorised workshop.
Restart motor.
Have it checked by an
authorised workshop.
Check whether the battery is
fitted correctly in the battery
compartment, correct if
necessary and restart motor.
Have it checked by an
authorised workshop.
Clean grass from cutting
area/ejector channel, remove
blockages (remove safety
key before hand K2 !).
When mowing on a slope:
Reduce speed or switch off
drive. Mow at right-angles to
the slope, not up and down.
Charge battery.
Allow the mower to cool.
Clean grass from cutting
area/ejector channel, remove
blockages (remove safety
key before hand K2 !).
When mowing on a slope:
Reduce speed or switch off
drive. Mow at right-angles to
the slope, not up and down.
Note the correct operating
sequence for starting the
cutter motor (see chapter
"Start the cutter motor").
Restart motor.
Have it checked by an
authorised workshop.
40 V DC motor
2800 rpm
2600 rpm
3000 rpm