Technical Data; Motor; Charger; Battery - Sabo SAU17002 Mode D'emploi

Cutting bar blunt.
Motor power
decreasing
Low battery capacity
Excessive grass waste in
the housing or ejection
channel.
Extreme vibration
Blade blunt.
Unclean cut, lawn is
yellow
Cutting height too low.
Mowing too fast.
Insufficient overlapping
of cuts when mowing.
Lawn becomes matted.
Turbo signal has not
Ejection blocked
been detected
J + K .
Cutting height too low for
grass that is too high.
Pushing mower too fast.
Grass not dry.
Cutting blade blunt.
The mulched grass
does not look good:
clumps, excessive cut
material, coarse cut
Mulching rule ignored
(cut max. 1/3 of grass
height; the grass height
to be cut must be less
than 10 cm)
Driving speed too high.
Grass accumulation
under the mower blade.
Insufficient overlap
between mowing lanes.
Grass is damp.
In case of faults and defects which have not been listed here, please contact the
nearest authorized dealer.
Repairs which require specialized knowledge should only be performed by a qualified
expert. Your authorized dealer will naturally also be glad to help if you do not wish to
perform the maintenance work described here yourself.

18 TECHNICAL DATA

Motor

Motor
Motor speed

Charger

See separate instructions for the charger.

Battery

See separate instructions for the charger.
fan and housing clean (remove

Mower

the safety key first K2 ).
40-ACCU
Have it sharpened and
balanced by an authorised
workshop Q .
Charge battery (see separate
instructions for the charger).
Clear the cutting
chamber/ejection channel of
grass, keep the gap between
fan and housing clean (remove
the safety key first K2 ).
Have it checked by an
authorized dealer
Have it sharpened and
balanced by an authorized
dealer Q .
Adjust to higher cutting height
43-ACCU
I .
Adjust mowing speed.
Tall grass conditions may
dictate that more overlapping
of cuts is required.
A lawn scarifier can remedy
the problem considerably
Empty the grass collector L .
Adjust to higher cutting height
I .
Adjust mowing speed.
Let grass dry.
Have it sharpened and
balanced by an authorised

Sound power level

workshop.
40-ACCU
Set higher cutting height I .
43-ACCU
Adjust speed.
Set higher cutting height I .

Sound pressure level

If grass is long, the mowing
lanes may need to overlap 40-ACCU
further.
Set higher cutting height I .
Allow the lawn to dry.
43-ACCU

Vibrations

40-ACCU
40 V DC motor
2800 rpm
43-ACCU
9
Housing
Cutting width
Cutting heights
Handlebar height adjustable
Sack volume
Weight
Length
Width
Height
Wheels front / rear
Bearings front / rear
Housing
Cutting width
Cutting heights
Handlebar height adjustable
Sack volume
Weight
Length
Width
Height
Wheels front / rear
Mount front
Mount rear
Guaranteed sound power level;
measured according to 2000/14/EC
Guaranteed sound power level;
measured according to 2000/14/EC
Emission sound pressure level at operator's workplace;
measured according to EN60335-2-77
Measuring inaccuracy; according to ISO 4871
Emission sound pressure level at operator's workplace;
measured according to EN60335-2-77
Measuring inaccuracy; according to ISO 4871
Vibrations on the lawnmower's handlebar;
measured according to EN 60335-2-77
Measuring inaccuracy; according to EN12096
Vibrations on the lawnmower's handlebar;
measured according to EN60335-2-77
Measuring inaccuracy; according EN12096
Impact-proof plastic (PP)
400 mm
Central, 24, 32, 40, 50, 60, 75 mm
3 heights
44 litres
19 kg
1400 mm
455 mm
970 mm
Ø 150 mm / Ø 180 mm
Cone ball bearings
Aluminium pressure die-casting
430 mm
Central, 22, 30, 35, 42, 50, 60, 80 mm
3 heights
55 litres
22.5 kg
1480 mm
500 mm
1000 mm
Ø 180 mm / Ø 180 mm
Cone ball bearings
Cone ball bearings
L = 89 dB(A)
wa
L = 93 dB(A)
wa
L = 78 dB(A)
pA
1.5 dB
L = 81 dB(A)
pA
1.5 dB
a = 1 m/s
2
hW
0.5 m/s
2
a = 0.5 m/s
2
hW
0.25 m/s
2