Using Your Drill Press - Scheppach DP16SL Traduction Des Instructions D'origine

2. Work on the left side of the drill.
3. Put a screwdriver in the front lower notch (1),
keeping it in place.
4. Remove the outer locknut (3) with a flat spanner
(SW14).
5. Leaving the screwdriver in the notch, loosen the
inner locknut (4) until the cut-out is released from
the boss (6). WARNING: Spring is under tension!
6. Using the screwdriver, carefully turn the spring
cap (2) anti-clockwise until you can press the
notch (1) into the boss (6).
7. Lower the spindle to the lowest position and hold
the spring cap (2) in place. When the spindle
moves up and down as desired, retighten the in-
ner locknut (4).
8. If it is too loose, repeat steps 3-5. If it is too tight,
repeat step 6 in reverse order.
9. Using a flat spanner, tighten the outer locknut (3)
against the inner locknut (4).
10. NOTE: Do not over-tighten and do not restrict the
movement of the spindle!
The angular play of the spindle (Fig. 10)
With the spindle in a low position, take it in your hand
and try to make it revolving about its axis. If there is
too much play, proceed as follows:
1. Loosen lock nut (A).
2. Turn the screw (B) clockwise to eliminate the play
but without obstructing the upward and downward
motion of the spindle (a little bit of play is normal).
3. Tighten the lock nut.

Using your drill press

Warning:
If you are not familiar with this kind of machine, take
advice from an experimented person. In any case
you should have read and understood the safety and
operational instruction before attempting to operate
this product.
Pivoting the table (Fig. 10+12)
Tip: The inclination display (A) only serves as orien-
tation for a rough angular adjustment. For precision
work suitable goniometers must be used.
1. In order to place the drilling table (B) in the tilted
position, loosen the hex-nut (C) with a flat span-
ner (SW19), remove the screw (D) used for 90°
fixing and set the desired table angle. Retighten
the hex-nut (C).
Adjusting table height (Fig. 10+12)
1. Loosen the table support lock handle (1).
2. Adjust the table (B) to the desired height. Use the
adjustment handle for height adjustment (2).
3. Re-tighten the table locking (1).
Note: it is better to lock the table to the column in a
position so that the tip of the drill bit is just slightly
above the top of the workpiece
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Installing drill bits
1. Insert drill bit intc chuck far enough to obtain max-
imum gripping of chuck jaws. (When using a small
drill bit do not insert it so far that the jaws touch
the flutes -spiral grocves -of the drill bit.)
2. Make sure that the drill bit is centered in the chuck
before tightening the chuck with the chuck key.
optional.
3. Tighten the chuck with the key so that the drill bit
cannot slip during the work.
Choosing speed and tensioning belt only dp16 sl
(Fig. 13)
m Attention! Before opening the hood belt guard
always switch off the power plug. Wait before
maintenance / adjustment operations always full
stop of the machine (risk of injury)! Never run the
drill with open V-belt covering. Never touch in
the running V-belt.
Tip: Safety switch
If you want to adjust speed you have to open the pul-
ley cover. The device switches off immediately to
avoid the risk of injuries.
1. You can set different spindle speeds on your pillar
drilling machine:
2. Once you have turned off the machine, you can
open the cover (B) by loosening the screw (A).
You will find all adjustment options for the spindle
speed on the cover (B) of the machine.
3. Relieve the drive belt pressure on the right side
of the machine head by loosening the wing screw
(A). Pull the right side of the motor towards the
spindle slightly to relieve fan belt pressure.
4. Place the fan belt around the relevant pulleys.
5. Push the right side of the motor back to tighten
the fan belt.
6. Retighten the wing nut (A). The fan belt should
have about 13 mm play when it is squeezed in
the middle.
7. Close the cover.
8. If the fan belt slips during operation, adjust the
belt tension.
Removing the chuck.
Open jaws of chuck as wide as they go by turn-
ing chuck sleeve anticlockwise (when viewed from
above).
Carefully tap chuck with mallet in one hand while
holding chuck in other hand to prevent dropping it
when released from spindle nose.
Depth stop (Fig. 14)
NOTE: When the clamping device is in the up-
per position, the tip of the drill has to be slightly
above the top of the work piece.
The depth stop enables control of the drilling depth.
To do this, set the desired drilling depth and secure it
using the knurled nuts (A) against the lower stop (B).
GB 25