Select Ducting Option; Ductwork Preparation; Plan Cabinetry - Thermador Masterpiece Serie Manuel D'installation

P L A N T H E I N S T A L L A T I O N

Select ducting option

A
D
The 5 basic discharge connections, left, right, rear, front and recirculation can
be achieved through A to F with the optional parts listed.
1. The downdraft blower system is designed for use with 8" (203mm)
round ductwork using a lexible blower or 6" (152mm) or 10" (254mm)
round ductwork using an inline or remote blower. (Purchase blowers
separately.): Six (6) different discharge connections are available:
A = 8" (203mm) Round, Left Discharge out of Flex Blower
B = 8" (203mm) Round, Right Discharge out of Flex Blower
C = 8" (203mm) Round, Down Discharge out of Flex Blower (Electrical
Panel to be mounted remotely)
D = 1-7/8" x 19" (48mm x 483mm), Left Discharge out of Housing to
Remote Blower or Flex Blower in remote location. Use 1-7/8" x 19"
1-7/8" x 19" (48mm x 483mm) to 6, 8, or 10" (152mm, 203mm, or
254mm) round transition ductwork as appropriate.
E = 1-7/8" x 19" (48mm x 483mm), Right Discharge out of Housing
to Remote Blower or Flex Blower in remote location. Use 1-7/8" x
19" (48mm x 483mm) to 6, 8, or 10" (152mm, 203mm, or 254mm)
round transition ductwork as appropriate.
F = 1-7/8" x 19" (48mm x 483mm), Rear Discharge out of Housing
to Remote Blower or Flex Blower in remote location. Use 1-7/8"
(48mm x 483mm) x 19" to 6, 8, or 10" (152mm, 203mm, or
254mm) round transition ductwork as appropriate.
2. For best performance: Choose the ducting option which allows the
shortest length of ductwork and a minimum number of elbows and
transitions. Check location of loor joists, wall studs, electrical wiring
or plumbing for possible interference.
Note: The manufacturer is not responsible for performance complaints
attributable to the duct section.
The device achieves its optimum performance by means of a short,
•
straight exhaust air duct and as large a pipe diameter as possible.
The optimum extraction performance is not achieved and fan noise
•
is increased if exhaust air ducts are long and rough and if there is a
large number of duct bends or diameters less than 6" (152mm).
The pipes or hoses for laying the exhaust air line must consist of
•
non-combustible material.
Seal the connection points of the ducts appropriately.
•
Ductwork must vent outside, not into attic spaces for example,
•
unless the available 'Non-duct Recirculation Kit' is used.
B
C
F

Ductwork Preparation

DUCTING RECOMMENDATIONS
Proper performance is dependent upon proper ducting. Local building
codes may require the use of make-up air systems when using ducted
ventilation systems greater than speciied cubic feet per minute (CFM)
of air movement. The speciied CFM varies from locale to locale. It
is the responsibility of the owner and the installer to determine if
additional requirements and/or codes apply to speciic installations.
DO NOT USE FLEXIBLE DUCT; it creates back pressure/ air turbulence
and reduces performance.
Always install a metal vent cover where the ductwork exits the house.
E
COLD WEATHER installations should have an additional backdraft
damper installed to minimize backward cold air low and a nonmetallic
thermal break to minimize conduction of outside temperatures as part
of the ductwork.
The damper should be on the cold air side of the thermal break. The
break should be as close as possible to where the ducting enters the
heated portion of the house.
MAKE-UP AIR: Local building codes may require the use of make-up air
systems when using ducted ventilation systems greater than speciied
CFM of air movement. The speciied CFM varies from locale to locale.
It is the responsibility of the owner and the installer to determine if
additional requirements and/or standards apply to speciic installations.
For safety reasons, ducting should vent directly outdoors (not into
an attic, underneath the house, into the garage or into any enclosed
space). The unit cannot be used in conjunction with a recirculation unit.
THERMADOR recommends not exceeding 50 ft. (15 m) of equivalent
®
duct.

Plan cabinetry

For left, right, or rear exhaust:
Allow at least 18" (457mm) for transition and elbow or blower.
For left / right exhaust:
A 30" (762mm) deep cabinet is recommended to align properly with
lex blower. Flex blower can be mounted to rear cabinet wall or to a
platform / frame (not provided) on the base of the cabinet loor. (See
lex blower instructions.)
Cabinet depths of 24" (610mm) to 30" (762mm) are required -
depending on the type of cooking appliance.
For some applications, gas or electrical connections will need to be
moved or routed around downdraft unit.
For gas cooktop installations make sure that a minimum 27 square inch
(174 cm 2 ) opening is provided in the toe-kick and cabinet base. Inadequate
ventilation of the cabinet below the cooktop may result in lame outage
when operating the fan on higher speeds.
Note: A cooktop sealing kit must be purchased for gas applications.
The kit includes hole covers for the toe-kick and cabinet base, as well as
a trim seal for the cooktop.
Page 9