Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
•
(Available as an optional accessory)
1
PINLOCK
®
INNER VISOR ASSEMBLY
1.1 Remove the visor.
1.2 Make sure that the inner surface of the visor is clean and check that the pin adjustment external levers are turned inwards.
1.3 Place the Pinlock
®
inner visor on the visor. WARNING: The silicone-sealed profile of the Pinlock
with the inner surface of the visor.
1.4 Insert one side of the Pinlock
1.5 Widen the visor and fasten the other side of the Pinlock
1.6 Release the visor.
1.7 Remove the protective film from the Pinlock
res to the visor.
1.8 Fit the visor in the helmet.
CHECKING AND ADJUSTING THE INNER VISOR STRETCHING
Check the correct system assembly by opening and closing the visor. Check that both visors are correctly fastened and do not move.
If the inner visor is not tightly fixed to the visor, move the external adjustment levers simultaneously upwards to increase the stretch
(Fig. 7). This operation must be carried out gradually. The maximum stretch is achieved when the pin adjustment external levers are
turned outwards.
WARNING!
The presence of dust between the two visors may produce scratches on both surfaces.
Scratched visors and inner visors may cause reduced visibility and must therefore be replaced.
Regularly check the correct stretching of the inner visor to prevent the same from moving and scratching both surfaces.
If the helmet visor fogs up and/or condensation forms between the visors, check both for system correct assembly and stretching.
An excessive and early stretch of the inner visor may result in excessive adherence against visor surface and/or permanent defor-
mations with subsequent inability to perform following adjustments correctly.
The extended use under special weather conditions may reduce system performance and result in partial fogging and problems of
condensation on the inner visor. In this case, remove the inner visor from the helmet visor and dry it with dry and lukewarm air to
restore system efficiency.
Intense sweating /breathing, the use under particular weather conditions (low temperatures, and/or high humidity and/or sudden
changes in temperature or heavy rain) and intense and prolonged use may affect the performance of the system and cause the fog-
ging or formation of condensation on the inner visor.
•
(Available as an optional accessory)
1
PINLOCK
®
INNER VISOR ASSEMBLY
1.1 Remove the visor.
1.2 Make sure that the inner surface of the visor is clean and check that the pin adjustment external levers are turned inwards.
1.3 Place the Pinlock
®
inner visor on the visor. WARNING: The silicone-sealed profile of the Pinlock
with the inner surface of the visor.
1.4 Insert one side of the Pinlock
1.5 Widen the visor and fasten the other side of the Pinlock
1.6 Release the visor.
1.7 Remove the protective film from the Pinlock
res to the visor.
1.8 Fit the visor in the helmet.
CHECKING AND ADJUSTING THE INNER VISOR STRETCHING
Check the correct system assembly by opening and closing the visor. Check that both visors are correctly fastened and do not move.
If the inner visor is not tightly fixed to the visor, move the external adjustment levers simultaneously upwards to increase the stretch
(Fig. 7). This operation must be carried out gradually. The maximum stretch is achieved when the pin adjustment external levers are
turned outwards.
WARNING!
The presence of dust between the two visors may produce scratches on both surfaces.
Scratched visors and inner visors may cause reduced visibility and must therefore be replaced.
Regularly check the correct stretching of the inner visor to prevent the same from moving and scratching both surfaces.
If the helmet visor fogs up and/or condensation forms between the visors, check both for system correct assembly and stretching.
An excessive and early stretch of the inner visor may result in excessive adherence against visor surface and/or permanent defor-
mations with subsequent inability to perform following adjustments correctly.
The extended use under special weather conditions may reduce system performance and result in partial fogging and problems of
condensation on the inner visor. In this case, remove the inner visor from the helmet visor and dry it with dry and lukewarm air to
restore system efficiency.
Intense sweating /breathing, the use under particular weather conditions (low temperatures, and/or high humidity and/or sudden
changes in temperature or heavy rain) and intense and prolonged use may affect the performance of the system and cause the fog-
ging or formation of condensation on the inner visor.
®
inner visor on one of the visor pins and hold it in position (Fig. 5).
®
®
inner visor and check that the entire silicone-sealed profile of the inner visor adhe-
inner visor on one of the visor pins and hold it in position (Fig. 5).
®
®
®
inner visor and check that the entire silicone-sealed profile of the inner visor adhe-
inner visor to the second pin (Fig. 6).
6
inner visor to the second pin (Fig. 6).
6
®
inner visor should be in contact
®
inner visor should be in contact
Publicité
Table des Matières
