Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
WARNING!
In this configuration, the chin guard cannot be closed again. Do not force the closing of the chin guard becau-
se it could cause damages in the helmet's closing mechanism. To close the chin guard, it is necessary to move the locking
slider to position P (Fig. B, lever downwards).
WARNING!!!
-
The protection level of this helmet whilst riding depends upon the configuration adopted by the user: total protection if
the chin guard and visor are closed, partial protection if the chin guard and/or visor are open.
-
Do not remove nor tamper with the fixing screws that connect the chin guard to the shell.
-
Do not use the helmet without the chin guard.
-
Do not use the helmet in case of faulty chin guard. Contact immediately a Nolan authorized dealer.
•
VISOR MECHANISM SYSTEM
1
VISOR DISASSEMBLY
1.1 Open the visor completely with the chin guard closed.
1.2 Press and hold the visor release button (A) towards the front of the helmet and release the rear inner visor fastening (B) from its
seat by pulling the visor outwards.
1.3 Let the visor slide forwards until the front inner fastening (C) releases from the mechanism (Fig. 4).
1.4 Repeat the same steps on the other side of the helmet.
Warning: Do not remove the visor's opening and closing mechanisms from the chin guard.
2
ASSEMBLY
2.1 With the chin guard closed, set the visor in open position by placing the inner visor fastenings (B) and (C) into their seats in the
visor mechanism (Fig. 4).
2.2 Insert the fastening (C) in the provided front seat and press the visor against the side mechanism in line with the rear fastening
(B).
2.3 At the same time push the visor release button (A) towards the front of the helmet until you hear the fastening click of the visor
to the mechanism.
2.5 Repeat the same steps on the other side of the helmet.
WARNING!
-
Make sure that the system is working properly. Open the visor. By lifting the chin guard, the visor closes automatically.
-
Do not use the helmet if the visor has not been assembled properly.
-
If the visor opening/closing mechanisms are not working properly or if such mechanisms get damaged, please contact
a Nolan authorized dealer.
WARNING!
In this configuration, the chin guard cannot be closed again. Do not force the closing of the chin guard becau-
se it could cause damages in the helmet's closing mechanism. To close the chin guard, it is necessary to move the locking
slider to position P (Fig. B, lever downwards).
WARNING!!!
-
The protection level of this helmet whilst riding depends upon the configuration adopted by the user: total protection if
the chin guard and visor are closed, partial protection if the chin guard and/or visor are open.
-
Do not remove nor tamper with the fixing screws that connect the chin guard to the shell.
-
Do not use the helmet without the chin guard.
-
Do not use the helmet in case of faulty chin guard. Contact immediately a Nolan authorized dealer.
•
VISOR MECHANISM SYSTEM
1
VISOR DISASSEMBLY
1.1 Open the visor completely with the chin guard closed.
1.2 Press and hold the visor release button (A) towards the front of the helmet and release the rear inner visor fastening (B) from its
seat by pulling the visor outwards.
1.3 Let the visor slide forwards until the front inner fastening (C) releases from the mechanism (Fig. 4).
1.4 Repeat the same steps on the other side of the helmet.
Warning: Do not remove the visor's opening and closing mechanisms from the chin guard.
2
ASSEMBLY
2.1 With the chin guard closed, set the visor in open position by placing the inner visor fastenings (B) and (C) into their seats in the
visor mechanism (Fig. 4).
2.2 Insert the fastening (C) in the provided front seat and press the visor against the side mechanism in line with the rear fastening
(B).
2.3 At the same time push the visor release button (A) towards the front of the helmet until you hear the fastening click of the visor
to the mechanism.
2.5 Repeat the same steps on the other side of the helmet.
WARNING!
-
Make sure that the system is working properly. Open the visor. By lifting the chin guard, the visor closes automatically.
-
Do not use the helmet if the visor has not been assembled properly.
-
If the visor opening/closing mechanisms are not working properly or if such mechanisms get damaged, please contact
a Nolan authorized dealer.
5
5
Publicité
Table des Matières
