Disposal And Recycling; Troubleshooting - PrimAster BS2000 Traduction Des Instructions D'origine

Electrical connection lines must comply with the rel-
evant VDE and DIN regulations. Only use connection
lines labelled with H05VV-F. The labelling of the con-
nection cable with the type specification is required.
AC motor
• The mains voltage must be 220 - 240 V~
• Extension cables up to 25 m long must have a
cross-section of 1.5 mm .
2
Connections and repairs of electrical equipment may
only be carried out by an electrician.
Please provide the following information in the event
of any enquiries:
• Type of current for the motor
• Machine data - type plate
• Machine data - type plate

14. Disposal and recycling

The equipment is supplied in packaging to preven it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The equip-
ment and its accessories are made of various types
of material, such as metal and plastic. Defective

15. Troubleshooting

Problem
Motor does not work
The motor starts up
slowly and does not
reach operating speed.
Motor makes excessive
noise
The motor does not
reach its full power.
Motor overheats easily.
Saw cut is rough or
wavy
Workpiece pulls away
and/or splinters
Saw blade is not running
straight
Burn marks appear on the
wood during the cutting
work
Saw blade jams during
cutting work
Possible cause
Motor, cable or plug defective, fuses burnt
Housing cover open (limit switch)
Voltage too low, coils damaged, capacitor
burnt
Coils damaged, motor defective
Circuits in the network are overloaded (lamps,
other motors, etc.)
Overloading of the motor, insufficient cooling
of the motor
Saw blade dull, tooth shape not appropriate for
the material thickness
Excessive cutting pressure and/or saw blade
not suitable for use
a) Guide has been wrongly set
b) Wrong saw blade
a) Blunt saw blade
b) Wrong saw blade
a) Blunt saw blade
b) Deposits on the saw blade
c) Guide has been set poorly
components must be disposed of as special waste.
Ask your dealer or your local council.
Old devices must not be disposed of with
household waste!
This symbol indicates that this product must
not be disposed of together with dome-
stic waste in compliance with the Directive
(2012/19/EU) pertaining to waste electrical
and electronic equipment (WEEE).
This product must be disposed of at a designated
collection point. This can occur, for example, by han-
ding it in at an authorised collecting point for the re-
cycling of waste electrical and electronic equipment.
Improper handling of waste equipment may have ne-
gative consequences for the environment and hu-
man health due to potentially hazardous substances
that are often contained in electrical and electronic
equipment. By properly disposing of this product, you
are also contributing to the effective use of natu-
ral resources. You can obtain information on collec-
tion points for waste equipment from your municipal
administration, public waste disposal authority, an
authorised body for the disposal of waste electri-
cal and electronic equipment or your waste disposal
company.
Help
Arrange for inspection of the machine by a
specialist. Never repair the motor yourself.
Danger!
Check fuses and replace as necessary
Close housing cover exactly
Contact the utility provider to check the voltage.
Arrange for inspection of the motor by a
specialist.
Arrange for replacement of the capacitor by a
specialist
Arrange for inspection of the motor by a
specialist
Do not use any other equipment or motors on
the
same circuit
Avoid overloading the motor while cutting,
remove
dust from the motor in order to ensure optimal
cooling of the motor
Resharpen saw blade and/or use suitable saw
blade
Insert suitable saw blade
a) Set the saw blade guide according to the
operating instructions
b) Select a saw blade according to the operating
instructions
a) Change the saw blade
b) Select a saw blade according to the operating
instructions
a) Change the saw blade
b) Clean the saw blade
c) Set the saw blade guide according to the
operating instructions
GB 29