Menu And Specific Features - Tivoli Audio PAL+BT Manuel Utilisateur

12. BACK: Press to go back to the previous menu page.
13. MONO: Press to change the Stereo/Mono setting. The display will show "ST" for stereo. "Mono" or "Stereo"
will also be one of the fields shown when pressing the Info button on the remote in FM mode. If you are listen-
ing to a noisy FM station in stereo, switching to mono may improve reception. Note: only FM mode can be
changed to Mono. Also see "Balance" under "Menu and Specific Features".
14. BATTERY HOLDER: Remove the protective strip protruding from the battery holder before using the remote
control. Should you ever need to replace the remote's battery, use Lithium button cell battery model CR2025.
CAUTION: Danger of explosion if the battery is incorrectly replaced. Replace only with the same or
equivalent type. Dispose of spent battery according to your country's regulations.

Menu and Specific Features

Press and hold the Menu button on the remote to enter the main menu. Use the remote's t u buttons and the
Select button to change the items within the menu. Use the Back button to navigate back, or wait for 15 seconds
until the timeout expires.
An asterisk (*) indicates the shown menu item is currently set.
SCAN SETTING (FM MODE ONLY): Press the Select button and use the pq and Select button to choose
1.
between "Strong stations only" or "All stations" when performing an Full Scan (see #9 (pq) under "Remote
Control"). Selecting "All stations" increases the sensitivity of the scan, possibly resulting in the Full Scan
stopping on noise. This feature is not accessible in Auxiliary mode.
EQUALIZER: Press the Select button and use the
2.
the following options: Normal, Classic, Jazz, Pop, Rock, and Speech. Press the Select button to enable the
desired EQ setting.
TIME (FOUND UNDER SETTINGS):
3.
Set 12/24 hour: Press the Select button and use the pq and Select buttons to choose a 12 or 24 hour clock
format.
Set Time/Date: Press the Select button and use the pq and Select buttons to adjust the hour and then minutes,
immediately followed by the date. You must set the Auto update to "No update" in order to set the time manually.
For more, refer to "Auto update" below.
Auto Update: Press the Select button and use the pq and Select buttons to choose between "Update from any",
"Update from DAB" (also DMB), or "Update from FM" (RDS). For any of the auto updates to work, you must
have consistent reception of DAB or FM RDS with a time/date signal provided. It could take up to a minute or
more for the clock to update. Tivoli Audio is not responsible for inaccurate time/date information provided
by the auto update signal.
To set the clock manually, select "No Update", and then select "Set Time/Date" under the "Time" menu using
the pq or t u buttons and the Select button to set the hour. Repeat to set the minutes and press Select to
save. Within this same "Time" menu are additional options to set the date format and 12/24 hour clock mode.
NOTE: During a power outage, the alarm time(s) and clock will be maintained by an integrated back-up
memory. When "Auto update" is set to "Update from any", the radio may find the clock signal from the
last listened station, even when the PAL+BT is in standby.
Set Date Format: Press the Select button and use the pq and Select buttons to choose the date format you
prefer.
BACKLIGHT (FOUND UNDER SETTINGS):
4.
Timeout: The backlight level is configured at the factory to be constant. However, you can customize the
backlight to automatically change to a "Dim level" setting after a fixed period of time whenever no controls
are used. Once a control on the unit or the remote is pressed, the normal backlight level is restored.
Press Select and use the pq and the Select buttons to set the amount of time it will take for the backlight
to change to the dim level from 10, 20 ,30, 45, 60, 90, 120, or 180 seconds, or to keep the timeout feature Off.
t u
buttons to select the desired EQ setting from
9 – ENGLISH