Explosion Protection - WAGNER PAINT CREW Mode D'emploi

Masquer les pouces Voir aussi pour PAINT CREW:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

GB
4. Careful Handling and Use of Power Tools
a)
Do not overload the tool. Use the power tool
designed for the work that you are doing. You
work better and safer in the specified performance
range if you use the suitable power tool.
b)
Do not use power tools whose switch is
defective. A power tool that cannot be switched on or
off is dangerous and has to be repaired.
c)
Remove the plug from the socket before carrying
out tool settings, changing accessories or putting
the tool away. This precautionary measure prevents
unintentional starting of the tool.
d)
Store unused power tools so that they are
inaccessible to children. Do not let persons use
the tool who are not familiar with it or who
have not read these instructions. Power tools
are dangerous when they are used by inexperienced
persons.
e)
Take proper care of your tools. Check whether
the moving parts function trouble-free and do
not jam, whether parts are broken or damaged
so that the tool function is impaired. Have
damaged parts repaired before using the tool. Many
accidents have their origin in power tools that have
been maintained badly.
f)
Use the power tool, accessories, insert tools, etc.
in accordance with these instructions and in a
fashion specified for this special tool type. Take
the working conditions and the activity to be
carried out into consideration. The use of power
tools for purposes other than the intended ones can
lead to dangerous situations.
5. Service
a)
Have your tool repaired only by qualified
specialist personnel and only with original spare
parts. This ensures that the tool safety is maintained.
a)
If the supply cord is damaged, it must be
replaced by the manufacturer or it's service
agent or a similarly qualified person in order to
avoid a safety hazard.
Health protection
Caution! Wear breathing equipment: Paint
mist and solvent vapors are damaging to
health. Always wear breathing equipment
and only work in well ventilated rooms
Danger
or
using
equipment. It is advisable to wear working
clothing, safety glasses, ear protection
and gloves
Flammable materials
Do not use the spray guns to spray
flammable substances.
Danger
20
supplementary
ventilating

Explosion protection

Do not use the unit in work places which
are covered to the explosion protection
regulations.
Danger
Danger of explosion and fire through
sources of flame during spraying work
There may be no sources of flame such
as, for example, open fires, smoking
of cigarettes, cigars or tobacco pipes,
sparks, glowing wires, hot surfaces, etc.
Danger
in the vicinity.
Electrostatic charging (formation of
sparks or flame)
Under certain circumstances, electrostatic
charging can occur on the unit due to
the rate of flow of the coating material
Danger
when spraying. On discharging this can
result in the emergence of sparks or fire.
It is therefore necessary that the unit is
always earthed through the electrical
installation. The connection must take
place through a correctly earthed two-
pole-and-earth socket outlet.
Ventilation
Good natural or artificial ventilation must be ensured in
order to avoid the risk of explosion or fire and damage to
health during spray work.
Secure device and spray gun
All hoses, fittings, and filter parts must be secured
before operating spray pump. Unsecured parts
can eject at great force or leak a high pressure fluid
stream causing severe injury.
Always secure the spray gun when mounting or
dismounting the nozzle and in case of interruption to
work.
Recoil of spray gun
In case of high operating pressure,
pulling the trigger can effect a recoil
force of up to 15 N.
Danger
If you are not prepared for this, your
hand can be thrust backwards or your
balance lost. This can lead to injury.
Continuous stress from this recoil can
cause permanent damage to health.
Max. operating pressure
Max. permissible operating pressure for spray gun,
spray gun accessories and high-pressure hose may
not fall short of the maximum operating pressure of
200 bar (20 MPa) stated on the unit.
Paint Crew

Publicité

Table des Matières
loading

Table des Matières