Effect Parameters; Effect Type List - Korg WAVEDRUM mini sondius xg Manuel D'utilisation

: Scale (temperament) [0...6]
Some sounds allow you to play phrases in a scale.
Some phrases will sound randomly with a different
pitch of the scale being heard each time you strike,
while for other phrases the pitch is determined by
the force of your strike. The scale can be specified
only for some of the sounds.
The right column of the table in "Sounds" (See page
68) contains a "O" for sounds that let you specify
the scale.
You can choose from the following scales.
0. Major, 1. Major Pentatonic, 2. Minor Pentatonic,
3. Minor, 4. India (Hanuma Todi), 5. Gamelan,
6. Tonic
With the 6. Tonic setting, the sound will be at the
pitch specified by the "Transpose" setting. For other
settings, refer to "Scale" (See page 69).
: Pad level [0...99]
Adjusts the volume of the sound output by the pad.
Use this to adjust the volume balance between the
pad and the clip.
: Clip level [0...99]
Adjusts the volume of the sound output by the clip.
Use this to adjust the volume balance between the
pad and the clip.
: Clip gain [0...99]
Adjusts the level of the input signal from the clip.
Adjust this as appropriate for the volume produced
by the object where the clip is attached.
: Rhythm level [0...99]
Adjusts the volume of the rhythm pattern.
: Speaker level [0...99]
Adjusts the output volume of the speaker. This set-
ting does not affect the OUTPUT or headphone
jacks.
: Auto power-off [Off, On]
With the On ( ) setting, the auto power-off func-
tion is enabled; the WAVEDRUM Mini will auto-
matically turn off the power approximately four
hours after the last panel operation was performed.
With the Off ( ) setting, the auto power-off func-
tion is disabled.

Effect parameters

Edit page no.: Parameter name [Default value]
: Effect 'a': Type select [0...9]
Selects the effect type for effect 'a'. For the available
effect types, refer to "Effect type list" below.
: Effect 'a': Dry/wet [0...99]
Adjusts the balance between the effect sound and
direct sound. With a setting of 0, only the direct
sound will be heard.
: Effect 'a': Parameter 1 [min...max]
: Effect 'a': Parameter 2 [min...max]
: Effect 'a': Parameter 3 [min...max]
These parameters edit the effect. The three parame-
ters will differ depending on the effect type. Refer
to "Effect type list" below.
: Effect 'b': Type select [0...9]
Selects the effect type for effect 'b'. For the available
effect types, refer to "Effect type list" below.
: Effect 'b': Dry/wet [0...99]
Adjusts the balance between the effect sound and
direct sound. With a setting of 0, only the direct
sound will be heard.
: Effect 'b': Parameter 1 [min...max]
: Effect 'b': Parameter 2 [min...max]
: Effect 'b': Parameter 3 [min...max]
These parameters edit the effect. The three parame-
ters will differ depending on the effect type. Refer
to "Effect type list" below.

Effect type list

Use or to select an effect type, and use
, , or ,
to edit the parameters. For every effect type,
and adjust the "dry/wet" balance.
Effect type 0: Reverb
This adds reverberation to the sound.
Parameter 1: Type [0...10]
Selects the type of reverb.
0: Off, 1: Slap, 2: Spring1, 3: Spring2, 4: Plate,
5: Garage, 6: Chamber, 7: Canyon, 8: Room,
9: Studio, 10: Hall
Parameter 2: Mix [0...99]
Adjusts the mix amount of the reverb sound.
Parameter 3: Depth [0...99]
Adjusts the duration of the reverb.
Effect type 1: Multi Tap Delay
This provides a multi-tap delay with three taps.
Delay creates an "echo-like" effect.
Parameter 1: Mode [0...4]
This specifies the combination of heads to use.
Editing the settings
, respectively
15