About This Documentation; Additional Documentation; Presentation Of Information; Warnings - Emerson AVENTICS MU1 Notice D'instruction

1 About this documentation

These instructions contain important information for the safe and appropriate as-
sembly and commissioning of the product.
Read these instructions carefully, especially
u
fore you start working with the product.

1.1 Additional documentation

1. Read and follow the operating instructions for the MU1 series maintenance
unit.
2. Also follow the instructions for the other system components.
3. Please also observe the generally relevant, statutory and other binding regula-
tions of European and national legislation and the national regulations for ac-
cident prevention and environmental protection in your country.

1.2 Presentation of information

1.2.1 Warnings

In this document, there are warning notes before the steps whenever there is a
danger of personal injury or damage to equipment. The measures described to
avoid these hazards must be followed.
Structure of warnings
Hazard type and source
Consequences of non-observance
Precautions
u
Meaning of the signal words
Possible dangerous situation.
Failure to observe these notices may result in minor injuries or damage to
property.

1.2.2 Symbols

Recommendation for the optimum use of our products.
Observe this information to ensure the smoothest possible operation.

2 Notes on safety

The product has been manufactured according to the accepted rules of current
technology. Even so, there is a risk of injury or damage if the following general
safety instructions and the specific warnings given in this instruction manual are
not observed.
1. Please read all these instructions carefully before working with the product.
2. Keep these instructions in a location where they are accessible to all users at
all times.
3. Always include the operating instructions when you pass the product on to
third parties.

2.1 Intended use

The product is exclusively intended for installation in a machine or system, or for
combination with other components to form a machine or system. The product
may only be commissioned after it has been installed in the machine/system for
which it is intended.
Use is permitted only under the operating conditions and within the performance
limits listed in the technical data. Only use compressed air as the medium.
The product is technical equipment and is intended for professional use only.
Intended use includes having fully read and understood these instructions, espe-
cially chapter g 2. Notes on safety.

2.2 Improper use

It is considered improper use when the product
AVENTICS™ MU1 | R412021818-BAL-001-AC | English
chapter g 2. Notes on safety
SIGNAL WORD
CAUTION
• is used for any application not stated in these instructions, or
• is used under operating conditions that deviate from those described in these
instructions.
be-

2.3 Personnel qualifications

All tasks associated with the product require basic mechanical, pneumatic and
electrical knowledge, as well as knowledge of the respective technical terms. In
order to ensure operational safety, these tasks may only be carried out by quali-
fied personnel or an instructed person under the direction of qualified personnel.
Qualified personnel are those who can recognize possible dangers and institute
the appropriate safety measures, due to their professional training, knowledge,
and experience, as well as their understanding of the relevant regulations per-
taining to the work to be done. Qualified personnel must observe the rules rele-
vant to the subject area.

2.4 General safety instructions

• Observe the valid local regulations to protect the environment in the country
of use and to avoid workplace accidents.
• Only use AVENTICS products that are in perfect working order.
• Examine the product for obvious defects, such as cracks in the housing or
missing screws, caps, or seals.
• The warranty will not apply if the product is incorrectly assembled.
• Do not place any improper mechanical loads on the product under any cir-
cumstances.
• Product warnings and information must be legible, i.e. not covered by paint,
etc.

2.5 Safety instructions related to the product and technology

• Lay cables and lines so that they cannot be damaged and no one can trip over
them.
• Do not operate the product in aggressive ambient air (e.g., solvent vapors).
• No soiling may be allowed to collect on or in the filters, reservoirs or windows.
Replace reservoirs if soiling cannot be removed from the drain (drain may be-
come clogged).

3 Scope of delivery

The scope of delivery includes:
• 1x filter (FLS) (according to the order)
• 1x condensate separator (according to the order)
• 1 set of operating instructions

4 Assembly, commissioning and operation

Danger of injury if assembled under pressure or voltage!
Assembling when under pressure or electrical voltage can lead to injuries and
damage to the product or system components.
1. Make sure that the relevant system component is without pressure and
voltage before you assemble the product.
2. Protect the system against being restarted.
Sudden pressure increase during commissioning!
If no SSU filling valve is used, the system will suddenly be under pressure dur-
ing commissioning! This may result in dangerous erratic cylinder motions.
When commissioning a system, make sure that the cylinders are in their
u
end position. For cylinders not in the end position, make sure they do not
present any danger.
CAUTION
CAUTION
8