Table des Matières
Publicité
PIECES AILES
(A) Aile (avec aileron et volet montés sur charnières et à coller) ................. (G/D)
.............................................................................................................1 de chaque
(B) Tringlerie ailerons et volets (tige filetée M3) ..................................................4
(C) Chape rotule avec visserie (vis M3x15mm+écrou nylstop+rondelle) ... 4 sets
(D) Guignol ailerons et volets ........................................................................ 4 sets
(E) Clé d'aile (tube carbone Ø35mm) ...................................................................1
(F) Vis fixation d'aile (plastique M4x16mm) .........................................................4
PIECES EMPENNAGES DIRECTION
(A) Empennage horizontal ...................................................................................1
(B) Fixation empennage hor. (vis M4x40mm+rondelle) ................................1set
(C) Dérive ..............................................................................................................2
(D) Fixation dérive (vis M3x20mm+ rondelle) ............................................. 4 sets
(E) Barre de renfort dérive ...................................................................................2
(F) Fixation barre de renfort dérive (vis M3x22mm+écrou M3+2 vis
M3x25mm+2 rondelles) ............................................................................... 2 sets
(G) Fixation servo direction (1 carénage plastique+2 blocs bois dur+4 vis à
bois 2,2x12mm) ............................................................................................ 2 sets
(H) Tringlerie de direction (tige fil. un bout M2+chape M2+écrou) ............ 2 sets
(I) Guignol direction ....................................................................................... 2 sets
PIECES EMPENNAGES PROFONDEUR
(A) Téton Ø6mm ....................................................................................................2
(B) Carénage de stab ............................................................................................1
(C) Tringlerie profondeur
(tige filetée M3)
(D) Chape rotule avec visserie
(vis M3x15mm+écrou nylstop+rondelle)
(E) Guignol profondeur .................................................................................. 2 sets
WINGS PARTS
(A) Wing
(with aileron and flap installed on their hinge point to be glued) ..................(L/R)
...................................................................................................................... 1 each
(B) Ailerons and flaps pushrod
(M3 threaded rod)
(C) Ball clevis with screws
(M3x15 screw+lock nut+washer)
(D) Ailerons and flaps control horn .............................................................. 4 sets
(E) Wing joiner
(Ø35mm carbon tube)
(F) Wing screw attachment
(plastic M4x16mm)
EMPENNAGES PARTS RUDDER
(A) Horizontal empennage ...................................................................................1
(B) Horizontal empennage fixing
(screw M4x40mm+washer)
(C) Fin and rudder .................................................................................................2
(D) Fin fixing
(screw M3x20mm+washer)
(E) Fin reinforcement bar ......................................................................................2
(F) Fin reinforcement bar fixing
(screw M3x22mm+nut M3 + 2 screws M3x25mm+2
......................................................................................................... 2 sets
washers)
(G) Rudder servo fixing
(1 plastic cover+2 hard wood blocks+4 tapping screws
...................................................................................................... 2 sets
2,2x12mm)
(H) Rudder pushrod
(M2 thread. rod one end+M2 clevis+nut)
(I) Rudder control horn ................................................................................. 2 sets
EMPENNAGES PARTS ELEVATOR
(A) Ø6mm dowel ....................................................................................................2
(B) Stab cover .......................................................................................................1
(C) Elevator pushrod
(M3 threaded rod)
(D) Ball clevis with screws
(M3x15mm screw+lock nut+washer)
(E) Elevator control horn .............................................................................. 2 sets
CONTENU DU KIT
...............................................................2
.......... 2 sets
KIT CONTENT
.................................................4
........................... 4 sets
......................................................................1
.......................................................4
...........................1set
......................................................... 4 sets
......................... 2 sets
.................................................................2
...................... 2 sets
PIECES CROCHET DE REMORQUAGE
(A) Crochet de remorquage (crochet+tige un bout fil.+chape M2+4 vis
M3x15mm+4 rondelles ..................................................................................1 set
PIECES TRAIN D'ATTERRISSAGE
(A) Train avant amorti
(avec amortisseur à gaz et axe de roue)
(B) Fixation train avant
(vis M5x30mm)
(C) Tringlerie dirigibilité
(avec chapes et silent-bloc "Servo-Saver")
(D) Train principal..................................................................................................1
(E) Fixation train principal
(vis M5x35mm+écrou nylstop M5) .............................
(F) Axe de roue train principal
PIECES MOTEUR
(A) Fuselage .........................................................................................................1
(B) Capot moteur ..................................................................................................1
(C) Fixation capot moteur (vis à bois 3x14mm) ...................................................7
(D) Réservoir 1500cc .....................................................................................1 set
(E) Tringlerie des gaz (avec chapes) ..............................................................1 set
(F) Verrière (ajustée sur son baquet-cabine) .................................................1 set
(G) Fixation cabine (vis M3x15mm+rondelle spéciale anti-desserrage) ..... 4 sets
(H) Fixation verrière (vis à bois 2x8mm) ..............................................................7
REMOTE TOWING HOOK PARTS
(A) Remote towing hook (hook+one side thread. rod+M2 clevis+4 M3x15mm
screws+4 washers ..........................................................................................1 set
LANDING GEAR PARTS
(A) Nose gear
(with gas shock and wheel axis)
(B) Nose gear fixing
(M5x30mm screw)
(C) Steering pushrod
(with clevises and "Servo-Saver" device)
(D) Main gear ........................................................................................................1
(E) Main gear fixing
(M5x35mm screw+M5 lock nut) .............................................
(F) Main gear wheel axis
(with 2 wheel stoppers)
ENGINE PARTS
(A) Fuselage .........................................................................................................1
(B) Engine cowl .....................................................................................................1
(C) Engine cowl fixing (self-tapping screw 3x14mm) ............................................7
(D) 1500cc gasoline tank ...............................................................................1 set
(E) Throttle pushrod (with clevises) ...............................................................1 set
(F) Canopy (fitted on its frame) ......................................................................1 set
(G) Canopy frame fixing (M3x15mm screw+special washer) ....................... 4 sets
(H) Canopy fixing (2x8mm self-tapping screw) .....................................................7
7
...............................1
..................................................................4
....................1 set
....................... 2 sets
(avec 2 bagues d'arrêt de roue)
........................................................1
..................................................................4
...........................1 set
............................................ 2 sets
4 sets
4 sets
Publicité
Table des Matières
