Control Knob - Migatronic RALLY MIG 161i Guide Rapide

RALLY MIG 161i CONTROL PANEL
I. Switch on the machine  select process
II. Select type of material and
wire diameter
III. Set one of the following parameters:
welding current, wire feed speed or
thickness of material
IV. Trim the arc length, if required
4 5
1 2 3
1. Selecting welding process MIG/MMA
Selecting welding process TIG under
secondary MMA parameters once MMA
process has been chosen.
2. Selecting type of material
Press the key until the LED is lit at the
relevant material.
3. Selecting wire diameter
Press the key until the LED is lit at the
relevant wire diameter.
Selection of AlMg/AlSi programs:
1. Select material the material type "Al"
2. Select material type 0.9 or 1.0 mm
3. Keep the material key pressed for 5 secs
until the "Al" LED is switched off as
indication of entrance to set-up mode.
The display shows
319 (0.9 mm AlMg ER5356),
359 (0.9 mm AlSi5 ER4043) or
369 (0.9 mm AlMg3Mn ER5554)
if 0.9 mm wire has been selected, or
312 (1.0 mm AlMg ER5356/ER5554),
352 (1.0 mm AlSi5 ER4043) or
A B
372 (1.0 mm AlSi12 ER4047)
6
if 1.0 mm wire has been selected.
4. Turn the control knob back and forth
until the correct program is displayed.
5. The program is selected by one more
press on the material key knob, and the
machine will return to normal mode.
Selection of CuAl/CuSi programs:
1. Select material the material type "Cu"
7
2. Select material type 0.8, 0.9 or 1.0 mm
3. Keep the material key pressed for 5 secs
until the "Cu" LED is switched off as
indication of entrance to set-up mode.
The display shows
501 (0.8 mm CuAl8 Brazing) or
561 (0.8 mm Cusi3 Brazing)
if 0.8 mm wire has been selected, or
509 (0.9 mm CuAl8 Brazing) or
569 (0.9 mm CuSi3 Brazing)
if 0.9 mm wire has been selected, or
502 (1.0 mm CuAl8 Brazing) or
562 (1.0 mm CuSi3 Brazing)
if 1.0 mm wire has been selected.
4. Turn the control knob back and forth
until the correct program is displayed.
5. The program is selected by one more
press on the material key knob, and the
machine will return to normal mode.
Reset function
Press and hold the key for 5 seconds. Flashing
LED indicates that the relevant program is
reset to factory settings.
4. Primary parameters
Set one of the following interdependent
primary parameters at your own option:
welding current, wire feed speed or thickness
of material.
Inching
Wire inching starts by pressing the green key
pad and simultaneously triggering the torch
trigger. Wire inching continues even though
the green key pad has been released. It does
not stop until the torch trigger has been
released again.
5. Arc length
The arc length can be adjusted as required.
Press the key under the symbol and turn the
control knob: plus (+) for a longer arc and
minus (-) for a shorter arc (-9.9 to +9.9).

6. Control knob

Adjustment of welding current, wire feed
speed, thickness of material or arc length.
Inching speed is adjustable during wire
inching. If the key for secondary parameters
is active, it is possible to trim the secondary
parameters.
QUICKGUIDE
RALLY MIG 161i
7. Secondary parameters
Press the key until the requested parameter
is shown on the display. Turn the control
knob until the requested value is displayed.
Press key 4 briefly to finish.
A. Welding voltage
B. Warning – overheating