Table des Matières
Publicité
Liens rapides
Publicité
Table des Matières
Manuels Connexes pour Oki OKIPAGE 10e
Sommaire des Matières pour Oki OKIPAGE 10e
- Page 1 Quick Start Guide Quick Start Guide...
- Page 2 Every effort has been made to ensure that the information in OKIDATA is a registered trademark of Oki Electric Industry this document is complete, accurate, and up-to-date. Company, Ltd.; Marque déposé de Oki Electric Industry OKIDATA assumes no responsibility for the results of errors Company, Ltd.;...
-
Page 3: Year 2000 Compliance
Year 2000 Compliance All products currently sold by Okidata are Year 2000 Compliant. Each product contains information technology that accurately processes date and time data between the years 1999 and 2000, and carries no issue for the September 9, 1999 (9999) programming concern. These products, when used in combination with products purchased from other manufacturers, whose products properly exchange data and time information, will accurately process the date and time. - Page 4 OKIPAGE 10e...
-
Page 5: Table Des Matières
Contents Overview Printer Software ............ 15 Year 2000 Compliance ........... 3 Printer Drivers ............... 15 Energy Star ..............3 Setting Up Your Printer .......... 6 No CD-ROM Drive? ............16 Status Monitor .............. 16 Selecting a Location for Your Printer ......6 Windows 95, Windows 98, and Windows NT 4.0 .. -
Page 6: Setting Up Your Printer
• Customer Support (minimum of 4 inches) • Software Drivers • A nearby power source • Corporate Information • Room temperature of 50° to 90°F (10° to 32°C) • Documentation • Relative Humidity of 20-80% • No direct sunlight OKIPAGE 10e... -
Page 7: Checking The Contents
Checking the Contents Unpack your printer. The shipping box should contain: 1 OKIPAGE 10e Printer (with image drum cartridge installed) 2 CD-ROM (includes printer drivers, software and User Manual) 3 Toner Cartridge 4 Black plastic light-shield bag (to store image drum if you... -
Page 8: Remove The Image Drum Protective Paper
Remove Protective Film Lift up the corner and peel the protective plastic film from the operator panel. Only the OKIPAGE 10 and 12 Series Type 5 Image Drum will fit in this unit (Part# 40433305) OKIPAGE 10e... -
Page 9: Installing Toner
Installing Toner 3 Peel tape off the bottom. 1 Remove the sponge. 4 Grasp the lock lever and place the left side of the toner cartridge under the end tab. 2 Unwrap the toner cartridge. Shake the cartridge to distribute the toner. Only the OKIPAGE 10 and 12 Series Type 5 Toner Cartridge will fit in this unit (Part# 52109001) Quick Start Guide... - Page 10 5 Lower the right side into the toner well, aligning the lock 6 When the cartridge is in place, push the lock lever forward lever slot with the ridge in the drum cartridge. until it stops. 7 Lower the printer cover and press firmly to close. E-10 OKIPAGE 10e...
-
Page 11: Loading Paper
Loading Paper 3 Fan a stack of paper and place it in the tray under the tabs. Do not fill above the “PAPER FULL” mark. 1 Slide the tray out of the printer. The paper gauge (1) indicates how much paper remains Recommended paper weight for the tray is 16 to 28 lb in the tray;... -
Page 12: Paper Exit Paths
2 Lift out the support bar. 1 Pull out the rear exit extender until it locks in place. Don’t change paper paths while printing − − − − − paper jam 2 Lift out the support bar. may occur. E-12 OKIPAGE 10e... -
Page 13: Choosing Paper
To return to the top exit, close the rear support bar and push When purchasing paper, use the following specifications for the rear exit extender firmly back in place, paper will then exit best results: into the top bin. Basic Weight See Operating Your Printer in the User’s Guide for Paper cassette: 16 to 28 lb (60 to 105 g/m information on using special print media. -
Page 14: Printing The Demo And Menu Pages
Part Number 70000803. See Service and Support in the User’s Guide for purchasing 2 Connect the other end of the cable to the proper connector information. on your computer. Fasten the cable securely to your computer. E-14 OKIPAGE 10e... -
Page 15: Turning On The Printer
The CD-ROM provided with your printer includes printer drivers and the on-screen printer status monitor and operator panel required to use all the OKIPAGE 10e features. Follow the steps in this guide to install the appropriate driver on your computer system. -
Page 16: No Cd-Rom Drive
MS 10692/0699 − Close all open applications. Windows 98 MS 10693/0699 − Insert the OKIPAGE 10e CD into the CD-ROM drive. − Click the Start button on the Windows taskbar, then Status Monitor click Run. The status monitor program allows you to monitor and −... -
Page 17: Windows 95, Windows 98, And Windows Nt 4.0
11 Restart Windows. Run. 12 Click the Start button on the Windows taskbar, then choose Programs→ → → → → OKIPAGE 10e. From the submenu, 4 Enter d:\install (assuming “d” is the location of your CD ROM drive). Click OK. -
Page 18: Installing The Standard Driver And The Status Monitor
Windows 3.x 4 Enter d:\install (assuming “d” is the location of your CD ROM drive). Click OK. The OKI Menu Installer Setup window appears. Installing the Standard Driver and the Status Monitor 1 Insert the disc into your CD-ROM drive. -
Page 19: Using The Status Monitor
11 Restart Windows. 12 Click the Start button on the Windows taskbar, then choose Programs→ → → → → OKIPAGE 10e. From the submenu, click Electronic Registration, Windows Status Monitor, or Readme.txt to see any of these programs. To register your printer online, visit the OKIDATA Web Site at http://www.okidata.com. -
Page 20: Using The Printer Menu Setup
, EPSON (7) Set print output quality, darkness setting. (8) Set power save, toner save. (9) Print demo page, font page, menu settings, cleaning page. Printer features set in your application software will override printer menu settings. E-20 OKIPAGE 10e... -
Page 21: Using Power Save To Minimize Warm-Up Time
If you want to remove the printer driver or status monitor 1 In Windows 95, click Start and select Programs. from your hard drive, use the following procedure: 2 Choose OKIPAGE 10e and click OKIPAGE 10e Status Monitor. Windows 95, Windows 98 and NT 4.0 The Status Monitor appears. - Page 22 Windows 3.x To remove the printer driver and status monitor: 1 From Program Manager double-click the OKIPAGE 10e icon (or the group where your printer is installed). 2 Double-click uninstallShield. 3 Restart your computer. E-22 OKIPAGE 10e...